Troubleshooting
Collar Receiver is not beeping or correcting. | • Check battery to make sure it is installed properly (page 12). |
| • Check that both lights are lit on the Fence Transmitter. If not, perform the “Short |
| Loop Test” (page 23). |
|
|
The Collar Receiver is beeping, but the dog is | • Make sure the Stimulation Level is set at 2 or above. |
not responding to the Stimulation. | • Test the Collar Receiver with the Test Light (6B, page 13). |
| • If the Test Light flashes, check the fit of the Collar Receiver (Step 9, page 16). |
| • Trim your dog’s hair where the Contact Points touch the neck and/or switch to |
| the longer Contact Points. |
| • Increase the Stimulation Level. |
| • Repeat training steps to reinforce training. |
The Collar Receiver has to be held on top of the | • Replace battery. |
Boundary Wire to activate. | • Adjust Range Adjuster knob clockwise to increase the distance from the |
| Boundary Wire that the Collar Receiver activates. |
| • Adjust the Range Switch to the other setting. |
| • If using a Double Loop, make sure Boundary Wires are separated 3 to 5 feet. |
| • If the Collar Receiver still has to be held on top of the Boundary Wire, perform |
| the “Short Loop Test” (page 23). |
|
|
The Collar Receiver activates inside the house. | • Turn the Range Adjuster knob counterclockwise to decrease the distance from |
| the Boundary Wire that the Collar Receiver activates. |
| • Make sure the Boundary Wire is not running too close to the house. The signal |
| can transmit through the walls of your house. |
| • Make sure Boundary Wires are twisted from Boundary to the Fence Transmitter. |
|
|
I have an inconsistent signal. | • Make sure the Fence Transmitter is at least 3 feet from large metal objects or |
| appliances. |
| • Make sure all Boundary Wire turns are gradual. |
| • Make sure the Boundary Wire is not running parallel to and within 5 feet of |
| electrical wires, neighboring containment systems, telephone wires, television |
| or antenna cables, or satellite dishes. |
| • If a neighboring containment system may be causing an inconsistent signal, |
| contact the Customer Care Center. |
The Power and Loop Indicator Lights are off. | • Check that the Power Adapter is plugged into the Fence Transmitter. |
| • Try plugging into another electrical outlet. |
| • Replace the fuses, refer to (Step 4C, page 11). |
| • If the lights still do not come on, the Fence Transmitter and/or Power Adapter |
| needs to be replaced. Contact the Customer Care Center. |
|
|
The Power Light is on, the Loop Indicator Light | • Make sure both ends of the Boundary Wire are plugged into Boundary Wire |
is off, and the Fence Transmitter loop alarm is | Terminals and that ½ inch of the insulation is stripped so that the copper wire is |
sounding. | exposed. |
| • Perform the “Short Loop Test” to determine if the Fence Transmitter needs to be |
| replaced or if the Boundary Wire is broken (page 23). |
| • If the Fence Transmitter is functioning properly, you have a break in your |
| Boundary Wire. See the “Locating a Break in the Wire” section in this guide |
| (page 24). |
|
|
The fuses blow when they are replaced. | • The Fence Transmitter and/or Power Adapter needs to be replaced. Contact the |
| Customer Care Center. |
Additional Information
• The system should only be used with healthy dogs. Contact your veterinarian if you have concerns about the medical condition of your dog (medication, pregnant, heart conditions, etc.).
• The SportDOG Brand®
• The Stimulation will get your dog’s attention, but will not cause harm. It is designed to startle, not to punish.
• Test the Collar Receiver every 3 to 6 months. Battery life depends upon how often the Collar Receiver is used.
• Remove the Receiver Collar from your dog when indoors for the comfort of your dog.
__________________________________________________
Short Loop Test
The Short Loop Test is a simple test to determine if each component (Fence Transmitter, Collar Receiver and Boundary Wire) is functioning properly.
1.Disconnect the Boundary Wire and Ground Wire.
2.Cut approximately 10 feet of unused Boundary Wire and connect it to the Boundary Wire Terminals.
3.Attach the Test Light to the Collar Receiver.
4.Spread the Boundary Wire out into a circle. Set the Range Switch to LOW.
5.Set the Range Adjuster knob to 10 and the Stimulation Level to level 2 or above.
6.If the Loop Indicator Light is not lit, then your Fence Transmitter is not functioning properly. Contact the Customer Care Center at
7.If the Loop Indicator Light is lit, disconnect one end of the Boundary Wire from the Boundary Wire Terminal.
8.If the loop alarm does not sound, the Fence Transmitter needs to be replaced. Contact the Customer Care Center.
9.If the loop alarm does sound, plug the Boundary Wire back into the Boundary Wire Terminal.
10.Hold the Collar Receiver next to the
11.If the Collar Receiver does not beep and the Test Light does not flash, replace the battery in the Collar Receiver. If it still does not beep and the Test Light does not flash, contact the Customer Care Center.
12.If the Collar Receiver beeps, there may be a complete or partial break in the Boundary Wire. See the “To Locate a Break in the Boundary Wire” section on the following page.
22 | |
SPORTDOG.COM | 23 |
3/5/10 4:28 PM