OPERATION

AUTOMATIC OILER ADJUSTMENT

1.Observe all safety precautions.

2.The automatic oiler is located in the front of the mo- tor housing. The oil volume can be adjusted with a 3/16 inch Allen wrench by turning the plug counter­ clockwise to increase output and turning clock­wise to decrease output.

NOTE:

Oil output varies proportionally to load and operat- ing pressure. It should be adequate for most opera- tions as adjusted from the factory.

3.Initial oiler adjustment is made with the saw bar and chain removed.

The following step can be hazard­ous. Failure to heed the instructions could result in serious injury.

4.Connect the pole chain saw to a hydraulic power source and check for proper operation. READ THE FOLLOWING CAREFULLY BEFORE PROCEED- ING.

a.Make sure the hydraulic power source is run- ning at the lowest gpm/lpm rate it can while still producing full pressure.

b.Secure the pole chain saw firmly in a bench vise and place the correct size wrench on the 1/2-20 nut securing the sprocket.

c.Connect the hydraulic power source to the pole chain saw and turn the circuit control valve to the ON position.

d.With a firm grip on the pole chain saw and wrench, SLOWLY squeeze the trigger to ac­ tivate it.

e.Adjust the oiler for a flow of approximately one drop every one to two seconds.

f.Release the trigger and remove the wrench.

CHAIN TENSION ADJUSTMENT

1.Observe all safety precautions.

2.When the chain appears loose, lubricate it well and let it cool for a few minutes to allow for contraction of the chain. Disconnect the pole chain saw from its hydraulic power source.

NOTE:

Perform Steps 3 through 6 while holding the top end of the saw bar upward.

3.Loosen the two saw bar nuts slightly.

4.Tighten the chain tension screw until the bottoms­ of the tie straps and cutters just touch the saw bar rails of the bottom of the saw bar.

5.Pull the chain around the saw bar by hand to be sure it fits the sprocket and saw bar properly. The chain should move easily.

6.Hold the saw bar tip up as you tighten the two saw bar nuts.

7.Connect the pole chain saw to a hydraulic power source. Operate the chain at low speed (gpm) for a minute or two while pumping extra oil on the chain.

8.Stop the pole chain saw and check the tension.

If it has loosened, disconnect the pole chain saw from the hydraulic power source and perform Steps 3 through 6 again to tighten the chain to the correct tension.

9.Reconnect the pole chain saw to the hydraulic pow- er source. Operate the saw and make a few easy cuts. Check chain tension and readjust if necessary (disconnect it from the hydraulic power source and perform Steps 3 through 6).

NOTE:

Never break in a new chain under a heavy cutting load.

10.Watch the chain tension carefully for the first half- hour of cutting.

16 ► CS25/28 User Manual

Page 15 Page 17
Page 16
Image 16
Stanley Black & Decker CS25/28 manual Automatic Oiler Adjustment, Chain Tension Adjustment
Page 15 Page 17

CS25/28 specifications

The Stanley Black & Decker CS25/28 stands out in the market of power tools, particularly for professionals in the construction and automotive industries. This tool represents a blend of advanced engineering and user-focused design, making it an essential piece of equipment for various cutting applications.

The CS25/28 is built with a powerful motor that delivers exceptional performance, ensuring that it can tackle heavy-duty tasks with ease. Its high RPM capability allows users to complete jobs quickly, saving valuable time on the job site. The tool's robust construction provides durability, allowing it to withstand the rigors of daily use in demanding environments.

One of the standout features of the CS25/28 is its ergonomic design. The tool incorporates a comfortable grip that reduces user fatigue, enabling extended use without strain. This is particularly important for professionals who rely on their tools for hours at a time. Additionally, the weight distribution of the tool has been optimized to enhance balance and control, making it easier to handle during intricate work.

The CS25/28 is equipped with several advanced technologies to enhance its cutting capabilities. For instance, it features a precision cutting blade that ensures clean and accurate cuts across various materials, including wood, metal, and plastic. The blade's design minimizes friction, which helps extend its lifespan and maintain cutting efficiency.

Another noteworthy technology is the tool's adjustable speed settings. This allows users to customize the cutting speed according to the material they are working with, providing flexibility and precision for different applications. The variable speed control ensures the best results whether engaging in delicate tasks or high-speed cutting.

Safety is paramount, and the CS25/28 comes with several integrated safety features. It includes a safety switch that prevents accidental startups, ensuring that the tool is only operational when the user intends it to be. Additionally, the sturdy blade guard offers added protection, making it safer for users during operation.

In conclusion, the Stanley Black & Decker CS25/28 is a versatile, powerful, and user-friendly tool that meets the needs of professionals across various industries. With its robust motor, advanced technologies, ergonomic design, and safety features, it stands as a reliable choice for anyone looking to invest in a high-quality cutting tool. Whether for construction, automotive repair, or DIY projects, the CS25/28 delivers exceptional performance and reliability.
Top Page Image Contents