Manuals / Brands / Computer Equipment / Computer Hardware / StarTech.com / Computer Equipment / Computer Hardware

StarTech.com TUEP2-M ECP, 4. BIOS SETUP, ECP DMA Select, Parallel Port Mode, ECP DMA Select [3], Parallel Port Mode, UART2 Use As [COM Port], ASUS TUEP2-MUser’s Manual

1 104

Download 104 pages, 3.95 Mb

4. BIOS SETUP

Onboard Serial Port 1 [3F8H/IRQ4]Onboard Serial Port 2 [2F8H/IRQ3]

These fields allow you to set the addresses for the onboard serial connectors. Serial Port 1 and Serial Port 2 must have different addresses. Configuration options: [3F8H/IRQ4] [2F8H/IRQ3] [3E8H/IRQ4] [2E8H/IRQ10] [Disabled]

UART2 Use As [COM Port]

When enabled, this field activates the onboard standard infrared feature and sets the second serial UART to support the infrared module connector on the motherboard. If your system already has a second serial port connected to the onboard COM2 connector, it will no longer work if you enable the infrared feature. Configuration options: [COM Port] [IR] [Smart Card Reader]

Onboard Parallel Port [378H/IRQ7]

This field sets the address of the onboard parallel port connector. If you disable this feature, Parallel Port Mode and ECP DMA Select configurations will not be available. Configuration options: [Disabled] [378H/IRQ7] [278H/IRQ5]

Parallel Port Mode [ECP+EPP]

This field allows you to set the operation mode of the parallel port. [Normal] allows normal-speed operation but in one direction only; [EPP] allows bidirectional parallel port operation; [ECP] allows the parallel port to operate in bidirectional DMA mode; [ECP+EPP] allows normal speed operation in a two-way mode. Configuration options: [Normal] [EPP] [ECP] [ECP+EPP]

ECP DMA Select [3]

This field allows you to configure the parallel port DMA channel for the selected ECP mode. This selection is available only if you select [ECP] or [ECP+EPP] in Parallel Port Mode above. Configuration options: [1] [3]

Onboard Game Port [200H-207H]

This field sets the address of the onboard game port connector. Configuration options: [Disabled] [200H-207H] [208H-20FH]

Onboard MIDI I/O [Disabled]

This field sets the address of the onboard MIDI connector. Configuration options: [Disabled] [330H-331H] [300H-301H]

Onboard CIR I/O [Disabled]

This field sets the address of the onboard Consumer IR connector. Configuration options: [Disabled] [2E0-2E8H] [3E0-3E8H]

4. BIOS SETUP

ASUS TUEP2-M User’s Manual

65

Contents

Page Product Name: ASUS TUEP2-M Manual Revision: 1.01 E807 Release Date: September ASUSTeK COMPUTER INC. (Asia-Pacific) Marketing Technical Support ASUS COMPUTER INTERNATIONAL (America) ASUS COMPUTER GmbH (Europe) Page 4.3.1 Primary & Secondary Master/Slave 5.1.1 Windows 98 First Time Installation TUEP2-MMotherboard Support CD 6.1.3 ASUS PC Probe Task Bar Icon 7. APPENDIX Federal Communications Commission Statement •This device may not cause harmful interference, and •Re-orientor relocate the receiving antenna •Increase the separation between the equipment and receiver •Consult the dealer or an experienced radio/TV technician for help 1.1How This Manual Is Organized 1.2 Item Checklist 2.1The ASUS TUEP2-M 2.1.1 Specifications CNR Support: Enhanced ACPI & built-in firmware-based Onboard LED: 2.1.2Specifications–OptionalComponents 2.1.3 Performance 2.1.4 Intelligence 2.2TUEP2-MMotherboard Components 2.2.1Component Locations 3.1TUEP2-MMotherboard Layout 3.2Layout Contents SETUP H/W 3.3Hardware Setup Procedure 3.4Motherboard Settings Motherboard Feature Settings 1) JumperFree™ Mode (JEN) 4.4 Advanced Menu NOTE: In JumperFree™ mode, all dip switches must be set to OFF Setting 2)USB Device Wake Up (USBPWR1,USBPWR2) NOTES 1.For suspend to RAM function, these jumpers must be set to Enable 3)CNR/USB Selection (CNRUSB1/CNRUSB2) CNR 4)Onboard Audio CODEC Setting (AUD_EN1) (available on audio model only) AUD_EN1 [2-3] 5)Onboard LAN Setting (LAN_EN) The onboard LAN may be enabled/disabled with this jumper 6)Keyboard Power Up (KBPWR) KBPWR 7)CPU External Frequency Setting (DSW) 1.In JumperFree mode, all dip switches must be set to OFF When JumperFree mode is enabled, use BIOS setup in place of these switches see CPU Internal Frequency External Frequency Table CPU:DRAM CPU Frequency Selection Switches Ratio 3.5System Memory (DIMM) 3.5.1 General DIMM Notes 3.5.2Memory Installation 3.6Central Processing Unit (CPU) 3.7Expansion Cards 3.7.1 Expansion Card Installation Procedure 3.7.2Assigning IRQs for Expansion Cards Standard Interrupt Assignments Interrupt Request Table for this Motherboard 3.7.3Communication and Networking Riser (CNR) Slot 3.7.4 Accelerated Graphics Port (AGP) Slot 3.8Connectors 3.8.1 External Connectors 3)Universal Serial BUS Ports 0 & 1 (Black two 4-pinUSB) USB Headers 4)Parallel Port Connector (Burgundy 25-pinPRINTER) Onboard Parallel Port 4.4.2 I/O Device Configuration) Serial Port Connectors (Teal/Turquoise 9-pin COM1 pin COM2) Onboard Serial Port 1/2 7)Audio Port Connectors (Three 1/8” GAME_AUDIO) (optional) Line Out Line In Mic 8)Fast-EthernetPort Connector (RJ-45)(optional) 3.8.2Internal Connectors 3)IDE Activity LED (2-pinIDELED) not place jumper caps over these pins 5)Internal Audio Connectors (4-pinCD1, AUX and MODEM) 6)Headphone True-LevelLine Out Header (3-pinHEADPHONE) 7)Internal Microphone Connector (3-pinMIC2) 8)ASUS iPanel Connector (24-1pin AFPANEL) 9)ASUS iPanel Audio Connector (10-1pin AAPANEL) 10)SMB Connector (6-1pin SMB) 11)Chassis Intrusion Lead (2-pinACHA) 12)Wake-On-LANConnector (3-pinWOL_CON) Wake On LAN or PCI Modem 13)Wake-On-RingConnector (2-pinWOR) NOTE: 14)USB Headers (10-1pin USB2) 3.4 Motherboard Settings USB Connect 15)ATX Power Supply Connector (20-pinblock ATXPWR) IMPORTANT: Make sure that your ATX power supply (minimum recommended 16)Smart Card Reader Connector (14-1pin SMART CARD) (optional) 17)System Power LED Lead (3-1pin PWRLED) 18)Keyboard Lock Switch Lead (2-pinKEYLOCK) 19)System Warning Speaker Connector (4-pinSPEAKER) 20)System Message LED Lead (2-pinMSG.LED) 21)System Management Interrupt Lead (2-pinSMI) 3.9Starting Up the First Time Award BIOS Beep Codes 4. BIOS SETUP Powering Off your computer: Start Shut Down Shut down the computer 4.1Managing and Updating Your BIOS 4.1.1 Upon First Use of the Computer System 1. Save Current BIOS to File Save Current BIOS To File A:\XXX-XX.XXX SETUP BIOS 4.1.2Updating BIOS Procedures Page 4.2BIOS Setup Program 4.2.1BIOS Menu Bar 4.2.2 Legend Bar General Help Saving Changes and Exiting the Setup Program Scroll Bar Sub-Menu 4.3Main Menu 4.3.1Primary & Secondary Master/Slave [User Type HDD] Cylinders Translation Method Head Sector Maximum LBA Capacity Multi-SectorTransfers [Maximum] SMART Monitoring [Disabled] PIO Mode [4] Ultra DMA Mode [Disabled] 4.3.2Keyboard Features A Note about Passwords BIOS Setup program and having full access to all configuration fields Forgot the Password Halt On [All Errors] Installed Memory [XXX MB] 4.4Advanced Menu USB Legacy Support [Auto] OS/2 Onboard Memory > 64M [Disabled] Notes for JumperFree Mode 4.4.1Chip Configuration SDRAM RAS Precharge Time SDRAM Cycle Time (Tras, Trc) [7T, 9T] SDRAM Page Closing Policy [One Bank] CPU Latency Timer [Enabled] Command Per Cycle [Enabled] Memory Hole At 15M-16M[Disabled] PCI 2.1 Support [Enabled] High Priority PCI Mode [Disabled] Onboard PCI IDE Enable [Both] SDRAM DATA DRIVING MODE [NORMAL] 4.4.2I/O Device Configuration Onboard Serial Port 1 [3F8H/IRQ4] Onboard Serial Port 2 [2F8H/IRQ3] UART2 Use As [COM Port] Onboard Parallel Port [378H/IRQ7] Parallel Port Mode 4.4.3PCI Configuration PCI IRQ Resource Exclusion 4.4.4Shadow Configuration 4.5Power Menu Video Off Option [Suspend ->Off ] Video Off Method [DPMS OFF] HDD Power Down [Disabled] Suspend-to-RAMCapability [Disabled] APIC Mode [Disabled] 4.5.1Power Up Control Wake On PS2 KB/PS2 Mouse/CIR [Disabled] Wake Up By PS2 Keyboard [Space Bar] Wake On PS2 KB/PS2 Mouse/CIR Wake On USB for S3 or S4 State [Disabled] USB Device Wake Up 4.5.2Hardware Monitor 4.6Boot Menu Boot Sequence Plug & Play O/S [No] Boot Virus Detection [Enabled] Quick Power On Self Test [Enabled] Boot Up Floppy Seek [Enabled] Full Screen Logo [Enabled] 4.7Exit Menu Exit Saving Changes Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes Page 5.1Operating Systems 5.1.1 Windows 98 First Time Installation 5.2 TUEP2-MMotherboard Support CD 5.2.1 Installation Menus 5.2.2 Applications ASUS Update Vx.xx: •Microsoft DirectX Driver: Installs Microsoft DirectX driver Microsoft DirectX Driver: Winbond Smart Manager Application: Adobe Acrobat Reader Vx.x: Page 6.1ASUS PC Probe 6.1.1 Starting ASUS PC Probe 6.1.2Using ASUS PC Probe Monitoring Settings History Fan Control Page Utility 6.1.3 ASUS PC Probe Task Bar Icon Page 6.2 Winbond Smart Manager 6.2.1 Setting Up Smart Manager Manager Smart Restart smart card reader 6.2.2Starting to Use Smart Manager 6.2.3Smart Manager Modes 6.3CyberLink PowerPlayer SE 6.3.1 Starting CyberLink PowerPlayer SE 6.3.2 CyberLink PowerPlayer Control Panel 6.4CyberLink VideoLive Mail 6.4.1Starting VideoLive Mail 6.7.2 CyberLink VideoLive Mail User Interface 6.5ASUS LiveUpdate 7.1 Glossary APPENDIX Boot Bus Master IDE Byte (Binary Term) COM Port LPT Port (Line Printer Port) MMX (Klamath) CPU as well as other OnNow PC100 ROM (Read Only Memory) SCSI (Small Computer System Interface) SDRAM (Synchronous DRAM) SPD for SDRAM module SSE (Streaming SIMD Extensions)