11.Close the water heater drain valve by turning the handle to the right (clockwise). The drain valve is on the lower front of the water heater.

12.Open the cold water supply valve to the water heater.

NOTE: The cold water supply valve must be left open when the water heater is in use.

13.To insure complete filling of the tank, allow air to exit by opening the nearest hot water faucet. Allow water to run until a constant flow is obtained. This will let air out of the water heater and the piping.

Never use this water heater unless it is completely full of water. To prevent damage to the tank and heating element, the tank must be filled with water. Water must flow from the hot water faucet before turning “ON” power.

14.Check element for water leaks. If leakage occurs, tighten element or repeat Steps 2 and 3, remove element and reposition gasket. Then repeat Steps 10 through 14.

15.Reconnect the two wires to the element and then check to make sure the thermostat remains firmly against the surface of the tank.

FIGURE 21.

16.Replace terminal cover on thermostat making sure the locking tabs on the terminal cover are in place.

17.Replace the insulation block and pad so that it covers the thermostat and element, see Figure 21.

18.Replace outer door.

19.Turn “ON” electric power to water heater.

FIGURE 22.

DRAIN VALVE WASHER REPLACEMENT

(See Figure 23)

1.Follow “Draining” instructions.

2.Turning counter clockwise ( ), remove the hex cap below the screw handle.

3.Remove the washer and put the new one in place.

4.Screw the handle and cap assembly back into the drain valve and retighten using a wrench. DO NOT OVER TIGHTEN.

5.Follow instructions in the “Filling The Water Heater” section.

6.Check for leaks.

FIGURE 23.

SERVICE

If a condition persists or you are uncertain about the operation of the water heater contact a service agency.

Use this guide to check a “Leaking” water heater. Many suspected “Leakers” are not leaking tanks. Often the source of the water can be found and corrected.

If you are not thoroughly familiar with your water heater and safety practices, contact a qualified installer to check the water heater.

18

Page 17 Page 19
Page 18
Image 18
State Industries 184748-001 instruction manual Drain Valve Washer Replacement, Service
Page 17 Page 19

184748-001 specifications

State Industries 184748-001 is a prominent water heater model that exemplifies advanced engineering and efficiency in residential and commercial applications. With a focus on reliability and energy savings, it is designed to meet the diverse needs of users while ensuring optimal performance.

One of the main features of the 184748-001 is its innovative insulation system. The water heater is equipped with high-density foam insulation that minimizes heat loss, which not only improves energy efficiency but also reduces operating costs. This feature makes it a suitable choice for those looking to lower their utility bills while still enjoying a consistent supply of hot water.

The 184748-001 utilizes a robust heating element that guarantees rapid recovery rates, ensuring that hot water is always available when needed. This model houses a powerful electric heating element that is designed for longevity and efficient operation. As a result, even during peak usage times, users can expect to have a steady flow of hot water, making it ideal for households with high demand or commercial applications.

In terms of capacity, the model can accommodate various needs, featuring a range of tank sizes to suit different households and facilities. Whether you're outfitting a large family home or a small business, the versatility of the 184748-001 allows it to adapt to a multitude of settings, ensuring that it meets the specific demands of each environment.

Another characteristic of this water heater is its user-friendly digital control panel. This feature allows for precise temperature adjustments, making it convenient for users to customize their hot water experience according to personal preferences. The digital interface also includes energy monitoring capabilities, providing insights into consumption patterns that help users make informed decisions regarding their energy usage.

Furthermore, State Industries has prioritized safety in the design of the 184748-001. Equipped with multiple safety features such as temperature and pressure relief valves, this model ensures that the system operates within safe parameters, reducing the risk of accidents and enhancing user confidence.

In summary, the State Industries 184748-001 water heater stands out for its combination of energy efficiency, robust performance, and user-friendly technologies. With its focus on safety and adaptability, it represents a smart investment for those seeking reliable hot water solutions for their homes or businesses.
Top Page Image Contents