CAUTION

This tank, as all tanks, will eventually leak. Do not install without adequate drainage provisions where water flow will cause damage. Note: normal condensation from a tank may appear to be a leaking tank.

The tank will work better if you keep the hot water runs short. You will also get hot water faster and with less heat loss.

The illustration shows the correct valves and fittings that you will need to install the tank. Threaded (3/4”) water connections are supplied through the tank top.

WATER PIPING

This tank is design certified to be used with a potable water system. When connecting water piping with solder joints use only lead free solder.

WARNING

HOTTER WATER CAN SCALD: Water heating tanks are intended to produce hot water. Water heated to a temperature which will satisfy clothes washing, dish washing, and other sanitizing needs can scald and permanently injure you upon contact. Some people are more likely to be permanently injured by hot water than others. These include the elderly, children, the infirmed, or physically handicapped. If anyone using hot water in your home fits into one of these groups or if there is a local code or state law requiring a certain temperature water at the hot water tap, then you must take special precautions. In addition to using the lowest possible temperature setting that satisfies your hot water needs, some type of tempering device, such as a mixing valve, should be used at the hot water taps used by these people or at the tank.

WARNING

This tank shall not be connected to any heating systems or component(s) previously used with a non-potable water heating appliance.

If this tank is also used for space heating applications, all piping and components connected to the tank shall be suitable for use with potable water.

This appliance has been design certified as a solar booster tank complying with Standards for Safety - UL174. The particular application of this appliance described (above paragraph) may be subject to review and approval by local code officials.

WARNING

Toxic chemicals such as used for treatment of boilers or non- potable water heating appliances shall never be introduced into a potable water space heating system.

WARNING

When the system requires water at temperatures higher than required for other uses, a means such as a mixing valve shall be installed to temper the water for those uses in order to reduce scald hazard potential. Mixing valves are available at plumbing supply or hardware stores. Follow manufacturer’s instructions for installation of these valves.

FIGURE 3

FIGURE 4

1.Buy the fittings that you need to connect the pipes. Remember that you have to connect both the hot and cold water pipes.

2.Apply a light covering of pipe joint compound to each outside thread before making connection.

3.Connect the cold water supply pipe to the cold water inlet of your tank as follows:

a.Look at the top cover of the tank. The hot and cold connections are marked there.

b.A non-metallic dip tube is supplied to carry cold water from the tank top to the bottom. Be sure that it is in the cold water inlet.

c.If using copper tubing, solder tubing to an adapter BEFORE you attach the adapter to the cold water inlet. DO NOT solder the cold water supply pipe directly to the cold water inlet connection. It might harm the dip tube.

d.The cold water supply line must have a shut-off valve and union.

4.Use a union to connect the hot water supply pipe to the tank’s hot water outlet.

CAUTION

Operating an empty or partially filled tank will result in damage to the tank.

If a tank is installed in a closed water system; such as one having a back flow preventer, check valve or water meter with check valve in the cold water supply line, means shall be provided to control thermal expansion. Contact the water supplier or local plumbing contractor on how to control this situation.

WARNING

INSTALLATION IN RESIDENTIAL GARAGES: The tank must be located and/or protected so it is not subject to physical damage by a moving vehicle.

FILLING THE GEOTHERMAL STORAGE

TANK WITH WATER

1.Close the tank drain valve. The drain valve is on the lower front of the tank.

2.Open the cold water supply to the tank. NOTE: THIS VALVE MUST BE LEFT OPEN WHEN THE TANK IS IN USE.

4

Page 3 Page 5
Page 4
Image 4
State Industries SGV 82 10TS, 198067-000, SGV 120 10TS Water Piping, Filling the Geothermal Storage Tank with Water
Page 3 Page 5

198067-000, SGV 120 10TS, SGV 82 10TS specifications

State Industries has a rich history in the manufacturing of high-quality water heaters and heating equipment, and two of its notable products, the State Industries 198067-000, SGV 82 10TS, and SGV 120 10TS, exemplify the company's commitment to innovation and efficiency.

The State Industries 198067-000 is an exemplary water heater designed for both residential and light commercial applications. It features a powerful heating element that ensures a quick recovery rate, providing users with an ample supply of hot water. With a capacity designed to meet various demands, this model stands out for its efficient performance and durability. The use of high-quality materials in its construction helps in maintaining a longer lifespan while minimizing the risk of leaks or failures.

The SGV 82 10TS model is particularly engineered for industrial applications, featuring a robust design that meets the rigorous demands of commercial users. One of its most remarkable features is its high thermal efficiency, which significantly reduces energy consumption while ensuring a steady supply of hot water. This model is equipped with advanced insulation to minimize heat loss, thus enhancing its overall operational efficiency.

In terms of technology, the SGV 120 10TS incorporates an advanced control system that allows for precise management of water heating cycles. This not only improves energy savings but also maximizes the system's performance according to real-time demands. The incorporation of advanced sensors provides seamless monitoring of temperature and pressure, ensuring optimal safety and efficiency in operation.

Both models are designed with user-friendliness in mind, boasting easy installation and maintenance features. An accessible design means that routine checks and servicing can be performed without significant effort, leading to prolonged equipment life and reduced downtime. Furthermore, these water heaters are compliant with various industry standards, ensuring that they meet safety and performance regulations.

Overall, the State Industries 198067-000, SGV 82 10TS, and SGV 120 10TS embody cutting-edge technology and reliable performance, making them top choices for users seeking efficiency, durability, and ease of use in their water heating needs.
Top Page Image Contents