ENGLISHGB

3.5 Throttle cable

1.Install the throttle cable on the engine if not al- ready installed. See the engine supplier’s man- ual.

2.Pull up the cable under the support’s (5:E) up- per section and over the screws in fig. 7.

3.Install the cable in the throttle. See fig. 11.

3.6 Cables

Pull up the cables under the cover under the sup- port’s (5:E) upper section and over the screws in fig. 7. Then install the ends into the relevant con- trol as follows:

1.Install the cable ends into the relevant control. The cable marked (R) must be installed into the reverse control. See fig. 9.

2.Install the cable’s adjuster sleeves into the slots in the handle. See fig. 10.

3.Slide the electric cable on the stop control’s flat pin. See fig. 11.

3.7 Gear lever

Install the gear lever (1:U) as follows:

1.Insert the gear lever (12:U) through the oval hole in the machine.

2.Install the washer (13:J) on the gear lever screw.

3.Press the gear lever’s ball into the lever socket.

4.Install the lock the (13:K) so that the gear lever locks into the lever.

5.Install the washer and nut (13:L) and tighten.

3.8 Rotor

Install the outer rotors (14:N) and cutting discs (14:O).

Note that the holes in shafts and sleeves must cor- respond before the screws are installed.

Install the screws with the stated lengths according to fig. 14.

3.9 Splash guards

Install the outer splash guards (15:M) with screws, nuts and washers according to fig. 15.

4 DESCRIPTION

The rotary cultivator is driven by a four-stroke en- gine and is intended for soil cultivation in private gardens. The most important parts and controls of the rotary cultivator are described below.

4.1 Reverse control (1:A)

The control is used to start the rotor for reverse when the engine is running.

Control in idle mode (released): No drive.

Control depressed: The machine reverses.

4.2 Drive control (1:B)

The control consists of a loop, positioned between the left and right handle.

The control is used to start the rotor for forward motion when the engine is running.

Control in idle mode (downward): No drive.

Control pressed up: Forward drive.

4.3 Stop (1:C)

The stop control is located in the middle of the throttle and has two positions as follows:

ON: The engine can be started and operated.

OFF: The engine stops and cannot be started.

4.4 Throttle (1:D)

The throttle controls the engine’s revs. Idle: Control in the rear position.

Full throttle and start: Control in the front position.

4.5 Handle (1:E)

The handle has two handgrips that are used to op- erate the machine over the area to be cultivated. The handle can be adjusted as follows:

•Laterally (angle) by releasing the lever (1:J).

•Vertically by releasing the knobs (1:S).

4.6 Fuel cap (1:F)

Unscrew the fuel cap to fill with petrol. The fuel cap must always be closed during operation.

4.7 Protective grille (1:H)

The protective grille must always be installed dur- ing operation. There are surfaces that become ex- tremely hot under the protective grille that risk causing personal injury if touched.

4.8 Cover (1:I)

The cover protects cables and the handle adjust- ment.

4.9 Oil filling (K)

Always check the oil level before start- ing the engine.

Plug for oil filler and checking the oil level.

43

Page 6 Page 8
Page 7
Image 7
Stiga 82R2-H manual Description
Page 6 Page 8

82R2-H specifications

The Stiga 82R2-H is a highly efficient, versatile ride-on mower designed for both residential and semi-professional use. This mower stands out in the market due to its robust build and innovative technologies, making lawn maintenance easier and more enjoyable.

One of the key features of the Stiga 82R2-H is its powerful Briggs & Stratton engine, which provides reliable performance and ensures that the mower can tackle even the most demanding mowing jobs. The engine is designed for optimal fuel efficiency while delivering a strong torque, which makes it suitable for various grass types and terrains.

The 82R2-H is equipped with a substantial cutting deck that measures 82 cm. This width allows for efficient mowing in larger areas while maintaining maneuverability around obstacles like trees and gardens. The cutting height can be easily adjusted, offering customization to suit specific turf conditions or user preferences. The mower provides seven cutting heights, ranging from 25 mm to 80 mm, allowing for a precise cut that promotes healthy grass growth.

Another standout feature is the innovative dashboard, which provides users with clear information about the mower's performance and maintenance needs. The intuitive controls are ergonomic, making it simple for users to operate the mower with minimal effort.

The Stiga 82R2-H also integrates advanced technology, such as mulching capabilities. This feature enables users to finely chop the grass clippings and return them to the lawn as nutrient-rich mulch, supporting environmental sustainability and reducing waste.

Moreover, the construction of the mower emphasizes durability and longevity. Its rugged chassis is built to withstand the rigors of frequent use, and the high-quality materials ensure that it maintains its performance over time. Additionally, the mower has a compact design that allows it to navigate narrow paths and tight spaces effortlessly.

Comfort is a priority in the design of the Stiga 82R2-H. It features an adjustable seat, allowing users to find the most comfortable position while mowing, which is crucial for longer mowing sessions. The mower’s low center of gravity enhances stability, making it safer and easier to handle.

In conclusion, the Stiga 82R2-H ride-on mower is a powerful, feature-rich machine that combines performance and convenience. With its strong engine, adjustable cutting options, and user-friendly design, it is an excellent choice for anyone looking to maintain a beautiful lawn with less effort. Whether for residential or semi-professional use, the 82R2-H is poised to meet the diverse needs of its users.
Top Page Image Contents