Stovax 7065Bl, 7057, 7061lG General Cleaning, Cleaning Glass, Chimney Sweeping, Annual Service

MAINTENANCE and SERVICING

See chart on page 11 for common spare parts refered to in this section.

For a complete list of spare parts and accessories contact your Stovax dealer for the

Stovax Fireplace, Stove & Hearth Accessories brochure or call 01392 474011

1. GENERAL CLEANING

Before any cleaning is carried out, allow stove to cool thoroughly to avoid risk of burns.

1.1We would recommend that your Huntingdon stove be cleaned fully on a regular basis, according to the level of use. Attention should be given to cleaning the baffle system, flueways and removing ash. Regular cleaning and preventive maintenance will help give many years of safe use.

1.2The external paintwork may be cleaned using warm soapy water and a soft clean cloth. Wipe dry with a soft clean cloth before re-lighting. Do not leave unit without drying, as this may cause rust. To refresh painted finishes it is possible to re-paint using Stovax Thermolac stove paint.

1.3Enamel finishes may be cleaned using warm soapy water and a soft clean cloth. Wipe dry with a soft clean cloth before re-lighting. Do not leave unit without drying, as this may cause rust. Do not use abrasive cleaner or cleaning pads to clean enamel finishes.

2.CLEANING GLASS

2.1While the correct use of the Airwash system, and good quality fuel, will generally keep the glass clean when the appliance is used you may sometimes need to clean the glass.

2.2This can be done as follows. Allow the Huntingdon stove to cool fully, never attempt to clean hot glass. Any deposits can be removed using a soft cloth and Stovax Glass Cleaner.

2.3Before re-lighting the appliance, dry the glass fully.

2.4Do not use abrasive cleaner or cleaning pads.

3.CHIMNEY SWEEPING

3.1We would recommend that to maintain the safe and efficient use of the appliance the flue / chimney is inspected and swept at least once a year, by a NACS registered (UK only)/INFO registered (Eire only) chimney sweep, who will issue you with a certificate.

4. ANNUAL SERVICE

At the end of the heating season it is recommended to strip, inspect and clean the stove as detailed:

4.1Carefully remove all of the following internal parts; baffle, firebricks, *complete grate, and *ashpan (*If multifuel

stove). See sections 5 and 6 for the instructions on how to remove the baffles and firebricks. Care should be taken when handling firebricks, as they can become fragile after a period of use.

4.2Vacuum clean any remaining ash and debris from the inside of the stove. Stovax offer a filter/collection attachment for your vaccuum cleaner to protect it from fire ash. Ash Clean (Stovax Part No. 2091).

4.3Clean the internal surfaces of the stove using a wire brush and scraper as required. Vacuum and brush the resulting debris from the stove.

4.4Clean the grate parts with a wire brush, and check the parts for any damage. Replace any damaged parts.

4.5Check and clean the firebricks with a soft brush. Replace any broken bricks. It is normal for some surface damage to occur during use and the life will depend on the type of fuels burnt and the level of use. Damaged bricks should be replaced as soon as possible.

4.6Re-fit cleaned internal parts.

4.7Remove the glass from the door, see section 7, and discard all old rope seals.

4.8Remove the door rope seal from the outer edge of the door and clean the old glue from the door sealing rope groove.

4.9Clean the door glass using Stovax Stove Glass cleaner and a soft cloth. Do not use abrasive cleaners to remove tar or soot deposits from the glass.

4.10Replace the glass edge seal with new and re-fit the glass into place in the door.

4.11Fit new door rope seal, gluing it in place with Stovax Thermic Seal rope adhesive. Press the new door sealing rope into the locating groove, placing the joint in the middle of the lower edge of the door. When fitting new door seals we recommend closing the stove door and leaving for at least 12 hours before using. This allows the adhesive to fully bond to the seal before use.

4.12Lightly oil the door catch mechanism and hinge pins. Avoid getting oil onto the door seals and glass.

4.13To refresh painted finishes it is possible to re-paint using Stovax Thermolac stove paint.

4.14We recommend that only genuine Stovax replacement parts are used to keep your appliance in safe and efficient working order. Your local Stovax dealer will be able to provide you with the genuine parts you require.

10