
P L E A S E R E A D A N D S AV E T H E S E
I M P O R TA N T S A F E T Y I N S T R U C T I O N S
A S S E M B LY I N S T R U C T I O N S
F E AT U R E S - O P E R AT I O N S
F E AT U R E S - O P E R AT I O N S
F E AT U R E S - O P E R AT I O N S
When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:
1.Read all instructions before using this heater.
2.This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. If provided, use handles when moving this heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9 m) from the front of the heater and keep them away from the sides and rear.
3.Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended.
4.Always unplug heater when not in use.
5.Do not operate any heater with a damaged cord or plug or after the heater malfunctions, has been dropped or damaged in any manner. Discard heater, or return to authorized service facility for examination and/or repair.
6.Do not use outdoors.
7.This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. Never locate heater where it may fall into a bathtub or other water container.
8.Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture or appliances. Arrange cord away from traffic area and where it will not be tripped over.
9.To disconnect heater, turn controls to off, then remove plug from outlet.
10.Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater.
11.To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, where openings may become blocked.
12.A heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint, or flammable liquids are used or stored.
13.Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
14.Always plug heaters directly into a wall outlet/ receptacle. Never use with an extension cord or relocatable power tap (outlet/power strip).
15.When unplugging, be sure to pull by the plug and not the cord.
16.If the heater will not operate, see specific instructions on Auto Safety
17.DO NOT attempt to repair or adjust any electrical or mechanical functions on this unit. Doing so will void your warranty. The inside of the unit contains no user serviceable parts. All servicing should be performed by qualified personnel only.
18.Discontinue use if plug or outlet is hot. It is recommended that the outlet be replaced if plug or outlet is hot to touch.
19.The heater must not be located immediately below a
SAVE THESE
INSTRUCTIONS
TECHNICAL SPECIFICATIONS | Figure 2 | ||
• Amps: 12.5 | |||
| |||
• Wattage: 1500W (+5% |
| ||
• Working voltage: 120V AC/60Hz |
| ||
NOTE: Low Heat setting may be 1000W on some models. |
| ||
ASSEMBLY INSTRUCTIONS |
| ||
NOTE: A Phillips screwdriver is required for assembly. |
| ||
Unpack your heater from box, being careful to remove |
| ||
all parts from plastic bags and remaining packaging. |
| ||
Please save the carton for |
| ||
Some models are packed with separate base and pedestal |
| ||
in the box. Carefully remove all parts from plastic bags. | Figure 3 | ||
To prevent scratches, place all parts onto a cloth before | |||
assembly. Follow the below instructions for Pedestal/ |
| ||
Base assembly: |
| ||
Pedestal Assembly (if no pedestal is included in this |
| ||
model, move to Base Assembly) |
| ||
Step 1: | Run the power cord through the center of the |
| |
| assembled pedestal. Snap pedestal into the |
| |
| bottom of the heater housing. Refer to Figure 1, 2. |
| |
Base Assembly |
|
Step 1: If the base is in two halves, snap them together by sliding slots of one base half into
slots of second base half. Refer to Figure 3. Figure 4
Step 2: Run the power cord through the center of the assembled base. To assemble the base to the unit (either one or
Step 4: Turn the heater right side up and place on a flat level surface prior to beginning operation.
REMOTE CONTROL (IF APPLICABLE)
If your heater comes with a remote control, unpack the remote control from box. This includes one lithium battery, CR2025/3V. Please note this remote control will not work through walls. Remove battery before discarding the remote.
NOTE: REMOVE THE PROTECTIVE COVER FROM THE BATTERY PRIOR TO BEGINNING OPERATION.
Battery Replacement
1.Locate the battery compartment on the back of the remote control handset. Insert a small object (such as a pin or paper clip) into the hole of the battery cover lock (see Figure 6) and slide out the battery cover.
Figure 6 | |
| A |
| Insert pin here |
| B |
A. | Battery Cover Lock |
B. | Battery cover |
2. Remove old battery. |
•Remove the used battery promptly.
•Do not discard used batteries into household trash containers. Contact your local government for disposal or recycling practices in your area.
FCC STATEMENT
Potential for Radio/Television interference
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and
(2)this device must accept any interference received,
including interference that may cause undesired operation.
This product has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. The product generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If the product does cause harmful interference to radio or television reception, which can be determined by turning the product on or off, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna. |
• Increase the separation between the product and the |
receiver. |
• Connect the product into an outlet on a circuit |
different from that to which the receiver is connected. |
• Consult the dealer or an experienced radio/TV |
technician for help. |
Figure 7 | CONTROL PANEL |
Temperature
Indicator
Lights
Timer Indicator
Lights
Dial Knob
Power Light Ring
REMOTE CONTROL (IF APPLICABLE)
NOTE: Avoid overloading your circuit by not using other high wattage appliances in the same outlet. At 1500 watts, this unit draws 12.5 Amps.
3. Operate heater by pressing the Power Button ( |
| ) and |
|
selecting modes and settings according to your preference. NOTE: Remove the plastic film from the control
Mode Selection
Select your desired heat settings by pressing the corresponding buttons as located on your heater or press the Mode button on remote control (if applicable) to cycle through the heat settings. An indicator light will illuminate next to each button to indicate that the selected setting/ mode is activated.
NOTE: Settings and control buttons may vary slightly between models.

Fan Only Setting
Press the Fan Only Button to run the heater without heat output. The Stay On temperature indicator light will remain illuminated.
HIGH Heat Setting
Press the Max Heat Button to run the heater continuously at 1500W. The Stay On temperature indicator light will remain illuminated.
LOW Heat Setting (if applicable)
Press the Low Heat Button to run the heater continuously at 750W. The Stay On temperature indicator light will remain illuminated.
Eco-Smart™ Setting (if applicable)
Press the
Thermostat Control
Your heater is equipped with a digital thermostat that allows you to set your heater to a precise comfort level by turning the Dial Knob or pressing the arrow buttons on the remote control (if applicable):
To preset a precise comfort level, turn the Dial Knob to adjust the temperature level ranging from 70°F to 85°F. The corresponding Temperature Indicator will illuminate once selected. When the preset temperature is reached, the heater will shut off and cool down for 15 seconds. When the room temperature drops below the preset temperature, the heater will automatically turn on again to maintain the preset temperature level.
FrostProtect™ Setting
To prevent frost, you may turn the Dial Knob to FrostProtect™ setting (), the heater will turn on automatically when the room temperature drops below 40°F.
NOTE: It is normal for the heater to cycle on and off to maintain the preset temperature. Raise the thermostat setting to prevent the heater from cycling. When the preset temperature is reached or when the heater is shut off, the fan will run for 15 seconds without heat. This cool down process ensures an accurate and consistent temperature reading.
NOTE: To shut the heater off at any setting, press the Power Button ( ) until all indicator lights go off. The heater will cool down for 15 seconds, and the Fan Only indicator light will blink in Amber until cool down is completed. The digital thermostat has memory; it will remember the last temperature setting before the heater is turned off. However, if the heater is unplugged, the digital thermostat will no longer remember the previous temperature setting. You will need to reset the digital thermostat if the heater is unplugged.


Oscillation (if applicable)
Press the Oscillation Button () either on the control panel or remote control (if applicable) to activate or stop
Timer (if applicable)
Some models are equipped with
1.Press the Timer Button ( ) once. The indicator light and the Power Light Ring will begin to blink for 5 seconds.
2.Turn the Dial Knob to cycle through the below sequence:
3.Select your desired interval for the heater to
4.To cancel the Timer feature, press the Timer Button
( ) twice within 5 seconds, and all Timer indicator lights will go off.
NOTE: The timer does not work with the FrostProtectTM Setting.
THIS APPLIANCE HAS A POLARIZED PLUG (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet.
DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS
SAFETY FEATURE IN ANY WAY.
Step 3: Lace the power cord through the cord minders on the underside of the base. Refer to Figure 5.
Figure 1 | Figure 5 |
|
3. | Place new battery into battery compartment. |
4. | Slide battery compartment into the remote control |
| handset until the Battery Cover Lock is securely |
| latched. |
5. | For your convenience, a remote control holder is |
| integrated into the back of the heater housing. |
NOTES
•Remove the battery from the equipment when it is not being used for an extended period of time.
• Changes or modifications not expressly approved by |
the party responsible for compliance could void the |
user’s authority to operate the equipment. |
OPERATING INSTRUCTIONS
1.Place heater on a firm, level surface.
2.Plug heater into a standard outlet. Once plugged in, the Power Light Ring will illuminate.
panel before using (if included).
Power On/Off
Press the Power On/Off Button to turn the heater on. Once on, the heater will run in the Max Heat mode and the Stay On temperature indicator light will illuminate. Press the Power On/Off button to manually turn off the heater at any setting.
NOTE: The Power Light Ring will remain illuminated while unit is plugged in.
NOTE: If your heater comes with a Thermostat Button ( ) on the control panel or remote control (if applicable), you may either press the button or turn the Dial Knob to activate.
the oscillation feature.
NOTE: Please do not manually turn the heater on the base. It is designed to turn only by motorized oscillation.
LEA Y GUARDE ESTAS
INSTRUCCIONES DE SEGURIDAD IMPORTANTES
I N S T R U C C I O N E S D E I N S TA L A C I Ó N
C A R A C T E R I S T I C A S Y F U N C I O N A M I E N T O
C A R A C T E R I S T I C A S Y F U N C I O N A M I E N T O
C A R A C T E R I S T I C A S Y F U N C I O N A M I E N T O
Para reducir el riesgo de incendios, descargas eléctricas y lesiones personales al utilizar electrodomésticos, siga siempre las precauciones básicas de seguridad, incluyendo las que se mencionan a continuación:
1. | Lea todas las instrucciones antes de usar este calefactor. |
2. | El calentador se calienta al usarlo. Para evitar |
| quemaduras, NO toque las superficies calientes con la |
| piel. Si existen, utilice las manijas para mover la |
| unidad. Mantenga los materiales combustibles, como |
| muebles, almohadones, sábanas, papeles, ropa y |
| cortinas a por lo menos 3 pies (0,9m) de la parte |
| delantera del calefactor y manténgalos alejados de los |
| costados y de la parte de atrás. |
3. | Debe tener mucho cuidado cuando el calefactor es |
| utilizado por, o cerca de niños o inválidos, y siempre |
| que se deje el calefactor prendido y desatendido. |
4. | Siempre desenchufe el calefactor cuando no lo utilice. |
5. | NO utilice el calefactor si el cable o el enchufe están |
| dañados o luego de una falla, se haya caído o haya |
| sufrido cualquier tipo de daño. Deseche el calefactor o |
| devuélvalo al centro de servicio autorizado para su |
| revisión y/o reparación. |
6. | NO utilizar en el exterior. |
7. | Este calefactor no está diseñado para ser utilizado en |
| baños, lavaderos y zonas similares de interiores. |
| NUNCA coloque el calefactor donde pueda caerse |
causar un choque eléctrico o incendio, o dañar el calefactor.
11. | Para evitar un posible incendio, no bloquee las |
| entradas de aire o escape de ninguna manera. No lo |
| use en superficies blandas, como una cama, donde las |
| aberturas se pueden bloquear. |
12. | Un calefactor tiene partes calientes y que pueden |
| producir chispas en su interior. NO lo utilice en áreas |
| donde se utiliza o se guarda gasolina, pintura o |
| líquidos inflamables. |
13. | Utilice este calefactor sólo como se describe en este |
| manual. Cualquier otro uso no recomendado por el |
| fabricante puede provocar incendios, descargas |
| eléctricas o lesiones a personas. |
14. | Siempre conecte el calefactor directamente a un |
| tomacorriente de pared. Nunca lo use con un cable de |
| extensión o con un tomacorriente múltiple. |
15. | Al desenchufarlo, asegúrese de tirar del enchufe y no |
| del cable. |
16. | Si el calefactor no funciona, vea las instrucciones |
| específicas del apagado automático de seguridad. |
17. | NO intente reparar o ajustar ninguna función eléctrica |
| o mecánica de esta unidad. El hacerlo invalidará la |
| garantía. La unidad no contiene partes reparables por |
| el usuario. Toda reparación debe ser realizada |
| únicamente por personal calificado. |
ESPECIFICACIONES TECNICAS
•Amperes: 12.5
•Potencia: 1500W (+5% –10%)
•Voltaje de funcionamiento: 120v CA/60Hz
NOTA: La configuración de Calor Bajo puede ser de 1000 vatios en algunos modelos.
INSTRUCCIONES DE INSTALACIÓN
NOTA: Se requiere un desarmador Phillips para el montaje. Saque el calefactor de la caja, tenga cuidado de sacar todas las piezas de las bolsas de plástico y del material restante de embalaje. Conserve la caja para almacenamiento del calefactor fuera de estación.
Algunos modelos incluyen en la caja una base y un pedestal separados. Sacar cuidadosamente todos los componentes de la bolsa de plástico. Para evitar arañazos, colocar todos los componentes en un paño antes del montaje. Siga las siguientes instrucciones de ensamblaje de la base/pedestal.
Ensamblaje del pedestal (si este modelo no incluye un pedestal, continúe en Ensamblaje de la base)
Paso 1: Pase el cable de alimentación a través del centro del pedestal ensamblado. Una el
Paso 4: Gire el lado derecho del calentador hacia arriba y coloque sobre una superficie plana antes de empezar la operación.
Figura 1
Figura 2
Figura 5
CONTROL REMOTO (SI CORRESPONDE)
El calefactor viene con control remoto; desembale el control remoto de la caja. Incluye una pila de litio, CR2025/3V. Tenga en cuenta que el control remoto no funcionará con paredes de por medio. Retire la pila antes de descartar el control remoto.
NOTA: RETIRE LA FUNDA PROTECTORA DE LA PILA ANTES DE UTILIZARLA.
Reemplazo De Pilas
1.El compartimiento para las pilas se encuentra en la parte posterior del control remoto. Inserte un objeto pequeño (como un alfiler o clip) en el orificio de la tapa de la batería de seguridad (ver Figura 6) y deslice la tapa de la batería.
5.Para su comodidad, encontrará un soporte para el control remoto en la parte posterior del armazón del calefactor.
NOTAS
•Quite las pilas del equipo cuando no lo vaya a usar por un período de tiempo prolongado.
•Reemplace las pilas que estén agotadas.
•No deseche las baterías usadas en contenedores de basura de la casa. Comuníquese con el gobierno local para informarse sobre las prácticas de reciclaje o de desecho de su zona.
DECLARACIÓN DE LA COMISIÓN FEDERAL DE COMUNICACIONES (FCC POR SUS SIGLAS EN INGLÉS)
Posibilidad de interferencias con Radio/Televisión
Este equipo cumple con la Parte 15 de las Normas de la FCC. Su funcionamiento está sujeto a las siguientes dos condiciones:
(1)Este equipo no puede causar interferencia perjudicial y
(2)este equipo debe aceptar toda interferencia recibida, inclusive interferencia que pueda causar un funcionamiento no deseado.
Figura 7 | PANEL DE CONTROL |
Indicadores de temperatura
Indicadores de temporizador
Perilla
Anillo de energía eléctrica
CONTROL REMOTO (SI CORRESPONDE)
( ) y seleccione modos y configuraciones de acuerdo con su preferencia.
NOTA: Retire la película plástica del panel de control antes de usarlo (si se incluye).
Encendido/Apagado
Presione el botón Encendido/Apagado para encender el calefactor. Una vez encendido, la temperatura del calefactor operará en modo Máxima temperatura y se encenderá el indicador de temperatura Permanecer encendido. Presione el botón Encendido/Apagado para apagar de manera manual el calefactor cualquiera sea la configuración.
NOTA: El anillo indicador de energía eléctrica permanecerá iluminado mientras la unidad se encuentre conectada.
Selección de modo
Seleccione las configuraciones de temperatura deseadas presionando los botones correspondientes de su calefactor o presione el botón Modo del control remoto (si corresponde) para recorrer las configuraciones de temperatura. Una luz indicadora se encenderá al lado del botón para indicar que se ha activado el modo o la configuración seleccionada.
NOTA: Las configuraciones y los botones de control pueden variar levemente según el modelo.
energía eficiente
Control de termostato
Su calefactor se encuentra equipado con un termostato digital que le permite configurar el calefactor en un nivel de confort preciso moviendo la perilla o presionando los botones con flechas del control remoto (si corresponde):
NOTA: Si su calefactor viene con el botón Termostato ( ) en el panel de control o en el control remoto (si corresponde), podrá presionar el botón o girar la perilla para activarlo.
Para configurar previamente un nivel de confort, gire la perilla para ajustar el nivel de temperatura entre 70°F y 85°F. El Indicador de temperatura correspondiente se encenderá una vez seleccionado. Cuando llegue a la temperatura preseleccionada, el calefactor se apagará y se enfriará durante 15 segundos. Cuando la temperatura ambiente esté por debajo de la temperatura
configuración, presione el botón Encendido ( |
| ) hasta |
|
que todas las luces indicadoras se apaguen. El calefactor se enfriará por 15 segundos y la luz indicadora de Sólo ventilador titilará en color ámbar hasta que se enfríe por completo. El termostato digital tiene memoria. Registrará la última configuración de temperatura antes que se apague el calefactor. Sin embargo, si el calefactor no está conectado, el termostato digital no registrará la configuración previa de temperatura. Deberá restablecer el termostato digital si se desconecta el calefactor.

Oscilación (si corresponde)
Presione el botón Oscilación ( ) del panel de control o del control remoto (si corresponde) para activar o detener la función de oscilación.
NOTA: No encienda manualmente el calefactor en la base. Está diseñado para encenderse únicamente ante oscilaciones motorizadas.
Temporizador (si corresponde)
Algunos modelos vienen con la función de temporizador de apagado automático a las 12 horas. Esto permite programar el calefactor para que se apague de manera automática luego de haber estado en funcionamiento por 4, 8 ó 12 horas.
| dentro de una bañera u otro recipiente con agua. |
8. | No coloque el cable debajo de la alfombra. No cubra el |
| cable con alfombras, tapetes o artículos similares. No |
| pase el cable por debajo de muebles o |
| electrodomésticos. Coloque el cable lejos del área de |
| tráfico y donde no se tropiece con él. |
9. | Para desconectarlo, gire el control a la posición OFF, |
| luego quite el enchufe del tomacorriente. |
10. | No inserte ni permita que objetos extraños penetren |
| en la ventilación o salida de aire ya que esto puede |
18. | Deje de usarlo si el cable o el enchufe se calienta. Se |
| recomienda que reemplace el tomacorriente si el |
| enchufe o el tomacorriente se calienta. |
19. | El calefactor no se debe localizar inmediatamente |
| debajo de un tomacorriente. No use este calefactor en |
| áreas cercanas a un baño, una ducha o una piscina. |
CONSERVE ESTAS
INSTRUCCIONES
pedestal al interior de la parte inferior del cuerpo del calefactor. Consulte la figura 1, 2.
Ensamblaje de la base
Paso 1: Si la base está en dos mitades, únalas deslizando las ranuras de una mitad de la base hacia las ranuras de la otra mitad de la base. Consulte la figura 3.
Paso 2: Pase el cable de alimentación a través del centro del base ensamblado. Para ensamblar la base a la unidad (ya sea una base de una o de dos piezas) compruebe primero que el lado marcado como “Posterior” esté orientado
Figura 3
Figura 4
Figura 6
A
B
Inserte aquí la clavija.
Este producto ha sido probado y se determinó que cumple con los límites para un dispositivo digital Clase B, según la parte 15 del reglamento de la FCC.
Estos límites están diseñados para brindar protección razonable contra interferencias nocivas en una instalación residencial. El producto genera, usa y puede irradiar energía de radiofrecuencia, y si no se lo instala y se lo usa según las instrucciones, puede causar interferencias adversas en las comunicaciones radiales. Sin embargo, no hay garantía de que la interferencia no ocurra en una instalación en particular. Si el producto causa interferencias nocivas en la recepción de radio o
•Pedir ayuda al distribuidor o a un técnico de radio/TV idóneo.
•Todo cambio o modificación que no haya sido expresamente autorizado por la parte responsable de exigir el cumplimiento podría anular la autoridad del usuario para usar el equipo.
INSTRUCCIONES DE USO
1. Coloque el calefactor en una superficie firma y nivelada. |

Configuración Sólo ventilador
Presione el botón Sólo ventilador para que activar el calefactor sin salida de calor. El indicador de temperatura Permanecer encendido quedará encendido.
Configuración temperatura ALTA
Presione el botón Temperatura máxima para que el calefactor funcione continuamente a 1500 W. El indicador de temperatura Permanecer encendido quedará encendido.
Configuración temperatura BAJA
preestablecida, el calefactor se encenderá nuevamente de manera automática a fin de mantener el nivel de temperatura preestablecido.
Configuración FrostProtect™
Para evitar la condensación, gire la perilla a FrostProtect™ Configuración ( ) y el calefactor se encenderá de manera automática cuando la temperatura ambiente baje a menos de 40ºF.
NOTA: Es normal que el calefactor se encienda y se apague para mantener la temperatura preestablecida.
1. | Presione el botón Temporizador ( ) una vez. La luz |
| indicadora y el anillo de energía eléctrica titilarán por 5 |
| segundos. |
2. Gire la perilla para que siga la siguiente secuencia: | |
3. | Seleccione el intervalo deseado en el que el calefactor se |
| apagará automáticamente. La luz indicadora de horario |
| correspondiente se encenderá, el anillo de energía |
| eléctrica y la luz indicadora del temporizador dejarán de |
ESTE PRODUCTO TIENE UN ENCHUFE POLARIZADO (una hoja es más ancha que la otra). A fin de disminuir el riesgo de descarga eléctrica, este enchufe está diseñado para insertarse en un tomacorriente polarizado en un solo sentido. Si el enchufe no entra completamente en el tomacorriente, inviértalo. Si aun así no entra, llame a un electricista calificado para instalar un tomacorriente apropiado.
NO MODIFIQUE EL ENCHUFE NI ANULE ESTA FUNCION DE SEGURIDAD
DE NINGUNA MANERA.
hacia la parte posterior del calefactor. Alinee los orificios de la base con los orificios de la parte inferior del pedestal (o del cuerpo del calefactor, si no se incluye un pedestal) y asegúrela con los 4 tornillos incluidos. Consulte la figura 4.
Paso 3: Ate el cable eléctrico con los minder de la cuerda en el superficie inferior de la base. Consulte la figura 5.
A.Traba de la tapa de la pila
B.Tapa de la pila
2.Quite la pila usada.
3.Coloque la pila nueva en el compartimiento.
4.Deslice el compartimiento de la pila hacia el control remoto hasta que la traba de la tapa de la pila se encuentre bien fija.
televisión, lo cual se puede determinar apagando y encendiendo el producto, se recomienda al usuario que intente corregir la interferencia por medio de una de los siguientes métodos:
•Reorientar o reubicar la antena receptora.
•Aumentar la separación entre el producto y el receptor.
•Conectar el producto a una salida en un circuito diferente de aquella a la cual está conectado el receptor.
2. | Conecte el calefactor en un tomacorriente estándar. |
| Una vez conectado, se encenderá el anillo de luz del |
| indicador de energía eléctrica. |
| NOTA: Evite sobrecargar el circuito eléctrico |
| evitando utilizar otro aparato de alta potencia en el |
| mismo tomacorriente. A 1500 Vatios, esta unidad |
| consume 12.5 Amperes. |
3. | Active el calefactor presionando el botón Encendido |
(si corresponde)
Presione el botón Temperatura baja para que el calefactor funcione continuamente a 750W. El indicador de temperatura Permanecer encendido quedará encendido.
Configuración Eco-Smart™ (si corresponde)
Presione el botón Eco-Smart™ para activar el modo de
Aumente la configuración del termostato para evitar que el calefactor se apague y se encienda. Cuando el calefactor llega a la temperatura preestablecida o cuando se apaga el calefactor, el ventilador continuará funcionando durante 15 segundos sin calor. Este proceso de enfriamiento asegura una lectura de temperatura precisa y uniforme.
NOTA: Para apagar el calefactor cualquiera sea la
titilar y se encenderán a los 3 segundos para de indicar |
que el temporizador seleccionado se encuentra activado. |
4. Para cancelar la función Temporizador, presione el |
botón Temporizador ( ) dos veces en 5 segundos y se apagarán todas las luces indicadoras del Temporizador.
NOTA: El temporizador no funciona con la configuración FrostProtectTM.
Sun_platform_HH_LED_12ESM1.indd 2
12/26/11 9:46 AM