FEATURES OF YOUR TURBO STEAM™ IRON
1. Covered Water Fill Hole |
|
| |
2. | Wait / Ready Light | 4 | 5 6 |
3. | Electronic / Digital Display |
| |
3 |
| ||
4. |
| ||
|
| ||
5. | Steam On/Off Buttons |
|
|
6. | Fabric Select Buttons | 2 |
|
7. | Turbo Steam™ Button |
|
|
8. | Shot of Steam ® Button / | 1 |
|
| Vertical Steam Button |
| |
|
|
| |
9. | Soft Grip Handle |
|
|
10. | Cord Lock™ Feature |
|
|
11. |
|
| |
12. | Translucent Water Reservoir |
|
|
9
7 8
10
an Cle
Figure A
wait 
ready
| with Max/Refill Lines | St |
|
| |
13. | Soleplate |
|
14. | Storage Strip™ Indicator |
|
o
rage
Strip |
| Toggle up to desired fabric |
| 11 | and wait for red light |
| 12 | to turn green. |
14 | 13 |
|
|
|
TO FILL THE WATER RESERVOIR
1.Make sure the iron is unplugged.
2.Lift the Water Fill Hole Cover.
3.Fill water cup with water. Pour water into iron water reservoir. Do not fill water reservoir beyond maximum fill level.
WARNING: To prevent the risk of burns, be careful when filling a hot iron with water. Hot metal parts, hot water and steam can cause injuries.
SELECTING FABRIC SETTINGS
To select a fabric setting, press the Fabric Select buttons (▲▼) until the desired fabric lights up (Figure A). The Wait/Ready light will change from red to green when the iron is ready to use.
NOTE: When using the SteamFunction,the iron will automaticallyadjust the steamto match the fabricselec- tion.
DRY IRONING
1.Plug the cord into a
2.Select Fabric Setting.
3.Press the Steam Off button.
NOTE: While in the Steam Off (Dry) setting, you may still use the Shot of Steam® feature or Turbo Steam™ feature. Please make sure the water reservoir is at least full to the Refill line.
TIP: Refer to the Ironing Guide for the recommended setting for your fabric.
STEAM IRONING
1.Follow theinstructionsfor “Tofill the WaterReservoir”.
2.Plug the cord into a
3.Select Fabric Setting.
4.When the green ready light turns on press the Steam On button.
TIP: Refer to the Ironing Guide for the recommended setting for your fabric.
USING THE IRON’S SPECIAL FEATURES
TURBO STEAM™ FEATURE
The Turbo Steam™ feature allows the iron to function as a powerful garment steamer. It can provide continuous pulsating steamfor up to 10 minutes and can be used horizontally or vertically.TurboSteamis ideal for steaming wrinkles out of delicate clothing, hanging garments and draperies.
To use Turbo Steam™:
1.Fill the water reservoir to the max fill line.
2.Hold the iron, either horizontally and iron normally or vertically, close to but not touching the fabric or garment to be steamed.
3.Using your free hand, keep the fabric pulled tight.
4.Press the Turbo Steam™ button once to turn the Turbo Steam™ feature on. Press the button again to turn it off. Turbo Steam will not turn on while in SYN or SILK fabric settings.
5.The Turbo Steam™ feature will start once the iron reaches maximum temperature.
IMPORTANT: The Turbo Steam™ pump action may cause the iron to vibrate slightly during use.
SHOT OF STEAM® / VERTICAL STEAM FEATURE
The Shot of Steam® / Vertical Steam feature provides an extra burst of steam for deep penetration of stubborn wrinkles. You can use this feature while Dry or Steam ironing, but the water reser- voir must be above the Refill line.
To use the Shot of Steam® / Vertical Steam Feature:
Place the iron on top of the wrinkle and press the Shot of Steam® button each time you would like an extra burst of steam. The Shot of Steam® feature may be used continuously with just a
short pause between shots in both the horizontal and vertical position.
WARNING: To prevent the risk of burns, keep your hand away from the area being steamed.
WARNING: DO NOT steam garments while wearing them; this may result in injuries.
