![5. Adjusting Armrest Receiver Fit](/images/new-backgrounds/56893/5689331x1.webp)
30 | I X . S e t - U p , A d j u s t m e n t & U s e | |||
5. Adjusting Armrest Receiver Fit |
|
| 4 | |
To tighten or loosen the fit of the outer armpost in the |
|
| ||
|
|
| ||
receiver: |
|
| 3 | |
| a. Loosen the four bolts on the sides of the receiver. |
| 5 | 8 |
| b. With the armrest in the receiver, squeeze the |
| ||
|
|
| ||
|
|
| 10 | |
| receiver to achieve the desired fit. |
|
| |
|
|
|
| |
| c. Tighten the four bolts. | 2 |
| 7 |
6. Adjusting Inner Armpost Fit |
| |||
|
| |||
|
|
| ||
| a. Two set screws are installed in the outer armpost. |
|
| 6 |
| b. Turn the set screws in or out until the desired fit |
|
| |
|
|
| 1 | |
| is achieved. |
|
| 9 |
|
|
|
|
I X . S e t - U p , A d j u s t m e n t & U s e | 31 |
H. WHEEL LOCKS |
|
Wheel locks are installed by Sunrise when requested on |
|
the Quickie |
|
1. Adjustment |
|
The wheel lock mounts on a split clamp system. Use a |
|
torque setting of 100 in./lbs when adjusting wheel |
|
locks. |
|
a. Loosen the screws on the side of each clamp. Do |
|
not remove the screws. |
|
b. Slide assembly toward rear wheel until clamp |
|
embeds into tire to prevent wheel movement |
|
G.FLIP-BACK HEIGHT-ADJUSTABLE ARMRESTS (OPTIONAL)
1.Height Adjustment
a.Release the upper securing lever.
b.Slide armpad up or down to desired height.
c.Return lever to locked position.
2.Flipping Armrest Back and Removing Armrest
a.Depress the release latch and pull arm toward back of wheelchair.
b.To remove, pull up on armrest. Pin securing armrest will automatically release.
c.To return armrest to operating position, push armpad down until it locks firmly into place.
Height-Adjustable
Armrest Key
1.Outer armpost
2.Standard receiver
3.Release lever
4.Armrest pad
5.Transfer bar
6.Side panel
7.Outer armpost tension adjustment set screws
8.Inner armpost
9.Receiver adjustment bolts 10.Release Lever
1 |
|
|
2 |
| 4 |
|
| |
3 |
|
|
| 6 | 5 |
|
|
when in locked position. |
c. Tighten screws. |
I. CHECK-OUT
Once the wheelchair is assembled and adjusted, it should roll smoothly and easily. All accessories should also perform smoothly.
After the wheelchair has been set up be sure the chair performs to your specified operational settings (see page 32). If the chair does not perform to specifica- tions, turn the wheelchair OFF immediately and repro- gram operational specifications using the QTRONIX Programming Pad.
Repeat this procedure until the wheelchair performs to specifications before attempting active use of the wheelchair.
If you have any problems, follow these procedures:
1. Review the |
and Operating Guide to make sure chair was |
properly prepared. |
2. If your problem persists, contact your authorized |
supplier. If you still have a problem after con- |
tacting your authorized supplier, contact Sunrise |
1.Armrest Pad
2.Upper Securing Lever
3.Release Latch
4.Armrest Panel
5.Rear Receiver
6.Armrest Receiver
customer service. See the introduction page for |
details on how to contact your authorized sup- |
plier or Sunrise customer service. |
930482 Rev. A | 930482 Rev. A |