Sunrise Medical V-100 Reaching Or Leaning, If You Must Reach Or Lean Do So at Your Own Risk

Models: V-100

1 25
Download 25 pages 52.07 Kb
Page 9
Image 9
REACHING OR LEANING

16

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

V

I

.

 

 

 

G

e

n

e

r

a

l

 

W

a

r

n

i

n

g

s

 

O.

REACHING OR LEANING

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Reaching or leaning affects the center of balance of your chair. If done improperly, a fall or tip-over is likely. When in doubt, ask for help or use a device to extend your reach.

To Reduce the Risk of injury and/or Damage to the Chair:

1.Never reach or lean if you must shift your weight sideways or rise up off the seat.

2.Never reach or lean if you must move forward in your seat to do so. Always keep your buttocks in contact with the backrest.

3.Never reach with both hands (you may not be able to catch yourself to prevent a fall if you lose your balance).

4.Never try to pick up an object from the floor by reaching down between your knees.

5.Never put pressure on the footrests while reaching. This may cause the chair to tip if you lean too far.

6.Never reach or lean over the top of the seat back. This may damage the backrest and cause you to fall.

If You Must Reach Or Lean; Do So at Your Own Risk.

Remember to:

1.Move your chair as close as you can to the object you wish to reach.

2.Rotate the front casters until they are as far forward as possible. This makes the chair more stable.

NOTE– To do this: Move your chair past the object you want to reach, then back up alongside it. Backing up will rotate the casters forward.

3.Turn off all power to your chair. If you fail to do so, you may touch the joystick and cause your chair to move when you do not expect it.

4.Firmly grasp a rear wheel or an armrest with one hand. This will help to prevent a fall if the chair tips.

P.DRESSING OR CHANGING CLOTHES

Be aware that your weight will shift if you dress or change clothes while seated in this chair. To make the chair more stable, rotate the front casters until they are forward.

To Reduce the Risk of injury and/or Damage to the Chair: V I . If You Must Reach Or Lean; Do So at Your Own Risk.P.DRESSING OR CHANGING CLOTHESG e n e r a l W a r n i n g s Q. OBSTACLESR.DRIVING IN REVERSES. RAMPS, SLOPES & SIDEHILLSBeware Of:Manual backgroundManual backgroundManual backgroundManual backgroundManual backgroundManual backgroundManual background 17

Q. OBSTACLES

Obstacles you may have to overcome in daily use include door thresholds, lifts, ramps and hazards such as potholes and broken pavement. These can damage your chair and may cause a fall, tip-over or loss of control.

1.Be aware that thresholds are very dangerous. (Even a small change in height may stop a caster wheel and cause your chair to tip). You may need to: •Remove or cover threshold strips between rooms.

•Install a ramp at entry or exit doors.

2.Keep your eyes moving when you ride; scan the area well ahead of your chair.

3.Make sure the floor areas where you use this chair are level and free of obstacles.

4.To help correct your center of balance:

•Lean your upper body forward slightly as you go up over an obstacle. •Press your upper body backward as you go down from a higher to a lower

level.

R.DRIVING IN REVERSE

Use extra care when you drive your chair in reverse. You may lose control or fall if one of the rear wheels hits an object.

1.Operate your chair slowly and at an even speed.

2.Stop often and check to make sure your path is clear of obstacles.

S. RAMPS, SLOPES & SIDEHILLS

The center of balance of your chair changes when you are on a slope.

NOTE– “Slope” includes a ramp or sidehill. Your chair is less stable when it is at an angle. Never use this chair on a slope unless you are sure it is safe. When in doubt, have someone help you.

Beware Of:

1.Steep slopes. Do Not use this chair on a slope steeper than 10%. (A 10% slope means: One foot in elevation for every ten feet of slope length).

2.Wet or slippery surfaces (such as when ice, snow, water or oil film is present). A loss of traction may cause a fall or tip-over.

3.A change in grade on a slope (or a lip, bump or depression). These may cause a fall or tip-over.

4.A drop-off at the bottom of a slope. (A drop-off of as small as 3/4 inch can stop a front caster and cause the chair to tip forward).

930482 Rev. A

930482 Rev. A

Page 9
Image 9
Sunrise Medical V-100 Reaching Or Leaning, To Reduce the Risk of injury and/or Damage to the Chair, Q. Obstacles