Page 8

SV Subwoofers

ion is the difficult job of the phase control. Essentially, “phase” varies the timing of the bass waves coming from the sub. But don’t despair if you don’t hear much differ- ence with changes to the phase knob — the effect of bass cancellation will vary by volume and frequency in your room, and no single setting is likely to ever be “perfect”. One simple technique to optimize phase is to find a nice “bassy” loop (such as the menu of the “Godzilla” DVD) and measure SPL response at various bass peaks. As the loop runs, you can have an assistant adjust the phase control. When you see the most response on a given bass passage, typically that’s the setting with the least room-induced cancellation (for the frequencies of the demo loop).

Line In/Out. Use either one of the sub’s “Line In” jacks to connect the subwoofer to the output jack of your receiver/processor. Feeding just one input is enough. If you are using a conventional amp and/or a stereo setup you can use the “Line Out” jacks to send sound (filtered of deep bass information) back to your system amp. A simple RCA to RCA cable is all you need for either type configuration.

Auto On. Your sub allows an “Auto On” mode… or can be on all the time. With the switch in the “Auto” position your subwoofer will “sense” that a DVD or CD etc. has begun and switch on immediately (the “hard power switch” mentioned below must be on, naturally). A few minutes after a movie finishes, the auto-on light will turn red, switching the sub back off. When running (and sensing a signal) the auto-on LED will be green. Sometimes, with very low listening levels, your subwoofer might not get enough of a bass signal from your surround sound processor to “trip” the auto-on circuit. Should you ever find this to be the case you may leave this switch to “On”, or turn the receiver’s subwoofer output up, and the sub’s volume down.

Crossover enable switch. If you allow your DD/DTS surround-sound receiver or processor to manage bass frequencies (again, highly recommended), this switch should be set to “Disabled”, eliminating the effects of the “Crossover Frequency” knob and allowing your sub to reproduce just what it’s fed from the receiver. If you use the sub in a two channel (stereo only) configuration, then “Enable” the crossover and adjust the knob to best blend the sub into the output of your speakers.

High level inputs/outputs. Not commonly used today, but binding posts are there in case you don’t have low-level inputs/outputs on your receiver/processor. Typically utilized only if you are not using a DD/DTS compatible system.

Power. This heavy-duty two-position switch next to the power cord will com- pletely cut the power to your sub amp. Flip this switch to off before you ever move the sub or change inputs or outputs.

A/C connection. Plug your sub into a dedicated A/C outlet. “Convenience” outlets of typical receivers often don’t provide the needed current. Avoid them.

Fuse. User replaceable, contact SVS if you have trouble finding one. The fuse can be accessed by a small round door immediately next to the power cord fitting.

Page 7 Page 9
Page 8
Image 8
SV Sound PB12-Ultra, PB12-Plus, PB12-ISD/V manual SV Subwoofers
Page 7 Page 9

PB12-Ultra, PB12-ISD/V, PB12-Plus specifications

SV Sound has made significant strides in the world of high-performance audio with its acclaimed lineup of subwoofers, including the PC12-Plus, PB12-Plus, PB13-Ultra, SB13-Plus, and PC13-Ultra. Each model is designed to deliver unparalleled sound quality and an immersive listening experience, making them ideal for both home theaters and music enthusiasts.

The PC12-Plus is a compact, ported subwoofer that boasts a 12-inch driver capable of producing thunderous bass. Its cabinet design optimizes airflow, reducing distortion while enhancing low-frequency output. The built-in amplifier delivers 300 watts of continuous power, with peak output reaching up to 700 watts, ensuring that every rumble is felt as much as it is heard. The PC12-Plus is also equipped with adjustable phase control and low-pass filters, allowing users to finely tune their bass response based on their room acoustics.

The PB12-Plus features a similar design but emphasizes portability and efficiency. Also utilizing a 12-inch driver, it emphasizes the ability to generate room-filling bass without compromising space. The built-in amplifier matches the PC12-Plus in power, promising rich low frequencies ideal for both cinematic action sequences and music playback alike. Its robust cabinet construction allows for minimal vibration and resonance, maintaining clarity in sound reproduction.

For those seeking uncompromising power, the PB13-Ultra is a standout. This subwoofer features a larger 13.5-inch driver and an impressive 1000 watts of continuous power, peaking at 3700 watts. This model is engineered for serious enthusiasts who demand deep-reaching bass extension, and it excels in both music and home theater settings. The advanced DSP technology provides users with precise control over the subwoofer’s settings, allowing for an incredibly adaptable performance.

The SB13-Plus is a sealed subwoofer that excels in delivering tight, accurate bass response. Its design minimizes distortion while maximizing punch, making it an excellent choice for music lovers who appreciate precision. This subwoofer is equipped with similar power specs to the PB12-Plus, offering 300 watts continuous and 700 watts peak power. Its compact design makes it versatile enough to fit in smaller spaces without sacrificing sound quality.

Finally, the PC13-Ultra combines elements from its predecessors with upgraded specifications. Featuring an ultra-long-throw 13.5-inch driver and an expansive amplifier setup, it can produce overwhelming bass that resonates throughout larger spaces. It incorporates advanced room correction technologies, ensuring optimal performance regardless of placement.

In summary, SV Sound’s PC and PB subwoofers are characterized by their robust design, powerful amplifiers, and advanced technologies. Each model serves unique needs, offering powerful bass while maintaining clarity and precision, from compact designs for finesse in smaller spaces to large models that dominate in larger environments.
Top Page Image Contents