OPERATION

Intended use: This log splitter is intended and designed to only split wood. NEVER use for any other purposes. Doing so can cause injury or VOID THE WARRANTY.

ASSEMBLY INSTRUCTIONS

This log splitter has been partially assembled at the factory. Refer to the drawings and part lists should it become necessary to disassemble the unit for repair or replacement of parts. Inspect all components for damage.

WARNING: Exercise extreme caution, as parts are very heavy. Sufficient persons or mechanical handling equipment should be used.

IMPORTANT: This unit is shipped without gasoline or oil in the engine. After assembly, see separate Engine Manual for proper fuel and oil recommendations.

1.General Assembly: Remove top, sides and ends of crate. Place crate panels aside to avoid puncturing tires. Remove tongue assembly from top.

2.Carefully set the beam pre-assembly aside.

3.Attach tongue to tank/mount plates using two bolts and nuts. Be certain hardware is secure. (See Assembly Figure 1)

4.Fender Assembly: Remove fenders from box. Mount to fender brackets with 5/16 hardware provided. Make sure fender clears wheel.

5.Remove tank/engine assembly from base of crate and discard banding. The cylinder is tied to the base. Remove ties and slide cylinder/wedge forward aligning clevis at cylinder end to beam. Insert pin and retaining clips, check component to assure proper assembly. Stand beam pre- assembly vertical and secure in position. Roll tank/engine assembly into place, aligning pivot holes. Bolt with provided hardware. Note: Do not over tighten; this is the vertical/horizontal pivot point.

6.Pivot beam assembly into the horizontal position and lock with pin provided.

7.Hose Assembly: Locate the Pressure Hose, noted by the pipe fittings, and attach it to the lower fitting on the valve. The remaining hose attaches to the top fitting of the valve. Secure with provided hose clamp.

8.Check both the horizontal and vertical positions for any “kinks” in the hoses. Note: Always make sure beam is locked securely into place.

See OPERATING POSITIONS for Horizontal to Vertical Splitting

START UP

WARNING: DO NOT START OR RUN THE LOG SPLITTER WITHOUT OIL IN THE ENGINE AND HYDRAULIC RESERVOIR.

See separate Engine Manual for fuel and oil recommendations. Your log splitter has come equipped with a fuel shut-off valve for towing purposes.

Before starting engine make sure crankcase is filled correctly with oil and the proper fuel has been used. The engine will only start when the throttle lever and fuel shut-off valve are turned to their ON positions.

COLD WEATHER START UP

The Cold Weather Clutch enables the engine to be started without having to pull through cold, thickened hydraulic fluid. Simply pull the handle out and slide into locked position. Start engine, let it warm up, and release Cold Weather Clutch. After starting, assure that the lever has reengaged.

Tank/Mount Plates

Assembly Figure 1

6

Page 5 Page 7
Page 6
Image 6
Swisher LS67528S owner manual Operation, Assembly Instructions, Cold Weather Start UP
Page 5 Page 7

LS67528S specifications

The Swisher LS67528S is an innovative log splitter designed for efficiency and ease of use. Built to handle a variety of wood sizes and types, this powerful tool ensures that users can tackle their splitting tasks with confidence and reliability.

One of the standout features of the LS67528S is its robust 675cc Briggs & Stratton engine. This powerful engine provides the necessary force to split logs quickly, reaching a maximum splitting force of 28 tons. Whether users are working with hardwoods like oak and hickory or softer woods like pine, this log splitter can handle the job with ease. The engine is designed for optimal fuel efficiency and minimal emissions, making it an environmentally friendly choice for those who are conscious about their carbon footprint.

The LS67528S is equipped with a hydraulic system that enhances its capability. The 2-stage hydraulic pump offers rapid cycle times, enabling users to split logs efficiently without unnecessary delays. Its integrated hydraulic log lift makes loading and unloading logs easy, alleviating the strain on users' backs and reducing the risk of injury.

Moreover, the sturdy steel frame of the LS67528S ensures durability and longevity. This rugged construction allows the log splitter to withstand the wear and tear of regular use, making it a reliable investment for homeowners and lumberjacks alike. The large, 12-inch wheels provide excellent maneuverability, allowing users to transport it to various locations easily, while the reinforced skid shoes enhance stability during operation.

The log splitter also features a versatile design, with a vertical and horizontal splitting option that provides added flexibility for different log sizes. Users can switch between orientations based on their needs, improving efficiency and making the LS67528S suitable for a wide range of tasks.

Safety is a priority in the design of the LS67528S. It comes equipped with safety features such as a protective guard and an automatic shut-off switch that ensures user protection during operation. This focus on safety, combined with the splitter's powerful performance and user-friendly design, makes the Swisher LS67528S an outstanding choice for anyone looking to make quick work of their firewood preparation or landscaping needs. With its advanced features and durable construction, the Swisher LS67528S stands out as a top performer in the market for log splitters.
Top Page Image Contents