SET UP FOR USE

You can program the tuner to scan all the channels you receive in your area.

NOTE: Channel memory programming is NOT needed when connected to a cable box or satellite box. Just select the TV/VCR channel selector to the output channel of the cable box or satellite box (Ex CH3). Then select the channel to be viewed on the Cable Box or Satellite Box.

CHANNEL SET UP FOR THE

FIRST TIME

1Plug in the TV/VCR power cord

Plug the TV/VCR power cord into a standard AC outlet.

NOTES:

You must disconnect the car battery cord from the TV/VCR before you use AC power.

If some digits appear in the corner of

the screen, press the POWER button without unplugging the power cord.

2Turn on the TV/VCR

Press the POWER button to turn on the TV/VCR.

3Select “ENGLISH” or “ESPAÑOL”

Select “ENGLISH” or

– SET UP –

“ESPAÑOL”=Spanish using the

B LANGUAGE

F.FWD/B or REW/s button. “[ ]”

[ENGLISH] ESPAÑOL

AUTO PRESET

indicate the selected language.

 

4 Begin auto preset

Press the PLAY/K or STOP/L but-

– SET UP –

 

ton to point to “AUTO PRESET”.

LANGUAGE

Then press the F.FWD/B button.

[ENGLISH] ESPAÑOL

B AUTO PRESET

The tuner scans and memorizes all

 

active channels in your area.

 

NOTES:

The TV/VCR distinguishes between standard TV

channels and cable channels.

TO SELECT A DESIRED CHANNEL

You can select the desired channel by using the CHANNEL K or L button or directly pressing the number buttons on the remote control.

Note for using the number buttons:

When selecting cable channels which are higher than 99, press the +100 button first, then, press the last two digits. (Example: to select channel 125, first press the +100 button then press “2” and “5”).

You must proceed single-digit channel numbers with a zero (Example: 02 ... 09).

CLOCK SET UP

(AUTO / MANUAL)

The TV/VCR clock must be set correctly before VCR timer recording is possible. It is suggested that the clock be set manually when first setting up the TV/VCR. Then, setup auto clock correction which will periodically correct the setting if necessary. NOTE: If you cannot receive a station with time signals, auto clock setting cannot be performed. Use manual setting only.

MANUAL CLOCK SETTING

Make sure ...

The TV/VCR is turned on.

In the example below, the clock is to be set to:

DATE

May 6th, 2003

SETTING TIME

5:40PM

If you want to play or record a video tape BEFORE

presetting the tuner, you must press the MENU but-

ton on the remote control. To preset the tuner again,

see “CHANNEL SET UP AGAIN” on page 13.

The TV/VCR may recognize TV channels to be

CATV channels by the receiving conditions. In this

case, try auto preset again in the fine receiving

conditions.

1Select “SETTING CLOCK”

Press the MENU button on the remote control.

Press the PLAY/K or STOP/L button to point to “SETTING CLOCK”.

Then, press the F.FWD/B button.

– M E N U –

TIMER PROGRAMMING PICTURE CONTROL

BSETTING CLOCK CHANNEL SET UP USER’S SET UP LANGUAGE [ENGLISH] ZERO RETURN

TIME SEARCH

5After scanning

The tuner stops on the lowest memorized channel. If you want to recall the selected channels, you can select the desired channel directly with the remote control number buttons or CHANNEL K or L button.

2Select “MANUAL CLOCK SET”

Press the PLAY/K or STOP/L

– SETTING CLOCK –

button to point to “MANUAL

AUTO CLOCK

[ON]

CLOCK SET”.

AUTO CLOCK CH SEARCH

AUTO CLOCK CH

[ 02 ]

 

B MANUAL CLOCK SET

 

Then, press the F.FWD/B button.

D.S.T.

[OFF]

 

 

- 11 -

EN

9J27

Page 11
Image 11
Sylvania 6309CD SET UP for USE, Channel SET UP for First Time, Clock SET UP Auto / Manual, To Select a Desired Channel