Sylvania 6620LDT Preparation for USE, ANTENNA/CABLE Connection, If YOU have a Jack on the Wall

Models: 6620LDT

1 44
Download 44 pages 32.69 Kb
Page 9
Image 9

PREPARATION FOR USE

ANTENNA/CABLE CONNECTION

NOTE

Cables used here are commercially available.

For your safety and to avoid damages to the unit, unplug the antenna cable from the ANT jack before moving the unit.

-ANTENNA/CABLE CONNECTION

IF YOU HAVE A JACK ON THE WALL

[Rear of this unit]

from Cable TV signal or Antenna

RF Cable

DIGITAL

 

 

 

 

 

 

OUT

 

 

 

AUDIO

 

 

 

 

 

(COAXIAL)

 

 

 

VID

EO

2

 

 

 

 

 

 

 

 

 

R

 

 

 

A

UD

IO

L

 

 

 

 

 

T

 

 

 

 

NEN

 

 

CPM

PO

 

 

 

 

Y

 

 

 

 

 

 

 

Pb

 

 

 

 

 

 

Pr

 

 

 

 

 

 

 

R

 

 

 

AU

DIO

L

 

 

 

 

 

 

VID

EO

1

VIDEO

 

 

 

 

 

 

 

 

IDE

O

 

 

 

 

S-V

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ANT

 

 

 

 

 

D PH

ONE

 

 

 

HEA

 

 

 

 

 

 

 

 

ANT

Connect the TV to the wall-mounted antenna jack with an RF cable (commercially available).

IF YOU HAVE A WIRED CABLE

Connect the TV to the wired antenna cable.

NOTE

Before plugging the antenna into the ANT jack of the unit, check that the pin is not bent. If it is bent, straighten the pin as illustrated, then plug the pin into the ANT jack of the unit.

Bent pin

Cable Plug

(Needs to be

(Straight pin)

straightened)

 

- CABLE/SATELLITE BOX CONNECTION

[Rear of this unit]

WHEN USING CABLE BOX/SATELLITE BOX

 

ITA

L

 

 

 

DIG

UT

 

 

IO OL)

 

 

AUDAXIA

 

 

 

(CO

 

 

 

 

 

 

 

EO

2

 

 

 

 

VID

 

 

 

R

 

 

 

 

 

 

 

AU

DIO

L

 

 

 

 

NT

 

 

CPM

PONE

 

 

 

 

Y

 

 

 

 

 

 

Pb

 

 

 

 

 

 

Pr

 

 

 

 

 

 

R

 

 

 

AU

DIO

L

 

 

 

EO

1

VI

DE

O

VID

 

 

 

 

 

S-VIDEO

 

 

 

 

 

ANT

 

 

 

 

D PH

ONE

 

 

HEA

 

 

 

 

 

 

 

ANT

NOTE

Cable Box

or Satellite Box

OUT IN

75-ohm Coaxial Cable

If your cable service supplies you with a converter box or if you use a satellite system, you can use the basic connection shown above.

Channel selection must be made with the converter box or satellite box. This means that channels cannot be changed using the remote control of this unit.

from Cable Company or Satellite dish

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and in particular, specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical.

- 9 -

EN

Page 9
Image 9
Sylvania 6620LDT Preparation for USE, ANTENNA/CABLE Connection, If YOU have a Jack on the Wall, If YOU have a Wired Cable