Hint
Hint
• To go back one step, press the sbutton
(during the steps [2] to [7].)
Your clock setting will be lost if either there
is a power failure or this unit has been
unplugged for more than 30 seconds.
Hint
Hint
• If you accidentally select Spanish or
French and need English:Press the
MENU button and choose SELEC.
IDIOMA, or SELECTION LANGUE.Press
the Bbutton, and select ENGLISH.Finally,
press the CLEAR/C.RESET button.
5
5
4
4
1
1
10 EN
Setup
Preset for Use
2
2
LANGUAGE SELECT
BENGLISH [ON]
FRANCAIS
ESPAÑOL
Hint
Hint
• Repeat these steps only if either there
was a power failure or this unit has been
unplugged for more than 30 seconds.
1
1
Turn on the TV and set it
to channel 3.
If channel 3 is already occupied for broadcasting,
see“RF Output Channel”section.
POWER
3
3CH 01
AUTO SET UP
To Preset the Channel Again
1) Press the MENU button until the main
menu appears.
2)Select "CHANNEL SET UP" by pressing
the Kor Lbutton.Then, press the Bbut-
ton.
3) Select "AUTO SET UP"by pressing the
Kor Lbutton.Then, press the Bbutton.
After scanning, the tuner stops on the low-
est memorized channel.
To Change the On-Screen Language
1) Press the MENU button until the main
menu appears.
2) Select "LANGUAGE SELECT" by press-
ing the Kor Lbutton.Then, press the B
button.
3) Select "ENGLISH" ,"FRANCAIS" or
"ESPAÑOL" by pressing the Kor Lbut-
ton.Then, press the CLEAR/C.RESET
button.

No

No

Please wait for a few minutes.
After scanning...
• The tuner stops on the lowest memorized
channel.
•You can select only the channels memo-
rized in this unit by using the CHANNEL
buttons.
If "AUTO SET UP" appears on the TV
screen again, check the cable connections.
Then, press the Bbutton once again.

Y

Yes

es Press the MENU
button to exit
• Refer to “Hint for Cable Box
or Satellite Box”section on
page 6.
Do you connect the cable from the cable box or
the satellite box to the DVD/VCR’s ANT IN jack?
YES
NO

Turn on the unit for the first

time

TV ScreenRemote Control
-MENU-
TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
BCLOCK SET
LANGUAGE SELECT
AUDIO OUT
TV STEREO [ON]
SAP
MENU
2
2CLOCK SET
MONTH DAY YEAR
0 3 / – – – – – –
HOUR MINUTE AM/PM
– – : – – – –
3
3CLOCK SET
MONTH DAY YEAR
0 3 / 1 5 – – – –
HOUR MINUTE AM/PM
– – : – – – –
CLOCK SET
MONTH DAY YEAR
0 3 / 1 5 MON 2 0 0 4
HOUR MINUTE AM/PM
– – : – – – –
CLOCK SET
MONTH DAY YEAR
0 3 / 1 5 MON 2 0 0 4
HOUR MINUTE AM/PM
0 5 : – – – –
6
6CLOCK SET
MONTH DAY YEAR
0 3 / 1 5 MON 2 0 0 4
HOUR MINUTE AM/PM
0 5 : 4 0 – –
7
7CLOCK SET
MONTH DAY YEAR
0 3 / 1 5 MON 2 0 0 4
HOUR MINUTE AM/PM
0 5 : 4 0 P M AM
BPM
Select the current month
Select the current day
Select the current year
Select “AM”or “PM”

8

8 To e xit the CLOCK SET
screen.
Select the current hour
Select the current minute

Clock Set Up

• If the clock is not set, the
CLOCK SET screen
appears when you press
the MENU button.In this
case, go to step [2].
To Select a Channel
You can select a channel by directly
entering channel using the Number but-
tons on the remote control.
Notes for using the Number buttons:
• When selecting cable channels which
are higher than 99, enter channel
numbers as a three-digit number.(For
example:117, press 1,1,7)
• You must precede single-digit channel
numbers with a zero (For example:
02, 03, 04 and so on).
VCRVCR
VCR
VCRVCR
VCR
or
or
or
or
or
or
or
or
VCR
VCR
VCR
VCR
H9600UD(EN)v1.qx33 03.12.8 10:50 AM Page 10