Manuals / Brands / Household Appliance / Smoke Alarm / System Sensor / Household Appliance / Smoke Alarm

System Sensor PDRP-1001 Series Installing Optional Voltmeter/Ammeter

1 56

Download 56 pages, 1.82 Mb

Installing Optional Voltmeter/Ammeter 2. Installation

PDRP-1001 Instruction Manual PN 50734:D0 04/06/01 15

Installing Optional Voltmeter/Ammeter

To monitor battery voltage and battery charging current, a 4XMM Meter Module is required. To install

the power meter module follow the steps below:

The figure below shows the mounting location and connections for the Voltmeter/Ammeter.

Figure 3 Mounting and Connecting the Meters

Step Action

1Cut the jumper wire labeled “AMP”.

2 Secure the module to the backbox with the hardware provided. Refer t o

Product Installation Drawing (PID) for detailed instructions.

3Connect meter cable P2 to connector J2 on the main circuit board.

4Connect meter cable P3 to connector J3 on the main circuit board.

AMP

TB5

010 20 30

DC VOLTS

DC AMPERES

MS44-mminst.cdr

‘AMP’ Jumper

Contents

Main PDRP-1001 Heat detectors are designed to protect property, not life. While a fire alarm system may lower insurance rates, it is not a substitute for fire insurance! Fire Alarm System Limitations Several different sources of power can be con- nected to the fire alarm control panel. FCC Warning System Reacceptance Test after Software Changes. Adherence to the following will aid in problem-free installation with long-term reliability: Installation Precautions NFPA Standards Before proceeding, the installer should be familiar with the following documents. NFPA Standards Underwriters Laboratories Documents Other Table of Contents 1. Product Description 2. Installation 3. System Operation Appendix A: Secondary Power Calculations Appendix B: Compatible Devices Appendix C: NFPA Standard-Specific Requirements Appendix D: Testing & Maintenance 1. Product Description Overview Features Options Circuits Input Circuits Output circuits Front Panel Control Switches Suplemental Documentation Control Panel Figure 1 Control Panel DIP Switch Functions Options Transmitter Module - 4XTM Zone Relay Module - 4XZM Remote Annunciator - RZA-4X LED Interface Module - 4XLM Meter Module (Volts-Amps) - 4XMM Specifications 2. Installation Cabinet Mounting Removal of Circuit Board Mounting of Cabinet Attaching Conduit Reinstallation of Circuit Board Reinstall the printed circuit board as follows: Step Action Installing Optional Voltmeter/Ammeter Power Connections AC Connections Battery (DC) Connections Power-limited Wiring Requirements 2. Installation PDRP-1001 Instruction Manual PN 50734:D0 04/06/01 17 Power-limited Wiring Requirements J2 AMP TB5 MS44-BATconn.cdr AC Power Initiating Device Circuits Four-Wire Smoke Detector Connections Output Circuits Notification Appliance Circuits TB2 Releasing Circuits ! TB2 TB2 Alarm Relay Circuit Trouble Relay Circuit Powering External Devices TB3 TB1 TB2 Optional Modules Overview Installation - Upper Position 2. Installation Optional Modules 24 Installation - Lower Position Figure 14 Module Installation - Lower Position To install either the 4XTM, 4XZM or 4XLM module in the lower position follow these instructions: Step Action Setup and Configuration Page Page 2. Installation Setting Mode of Operation 28 Setting Mode of Operation Figure 19 DIP Switch Settings Basic Program Select the desired mode of operation and set DIP Switches 1 and 2 per the appropriate column. Switch 1 Switch 2 Discharge Timer Power-Up Procedure ! 3. System Operation System Status LEDs Control Switches Zone Status LEDs Piezo Supervisory Service Zone Disable Last Event Recall Non-Silenceable Service Sprinkler Supervisory Tracking System Events Standby Condition Single Zone in Alarm (Cross Zone) Condition Both Zones in Alarm (Cross Zone) Condition Brownout Condition Page Appendix A: Secondary Power Calculations Standby Battery Requirements Calculating the Battery Capacity Appendix B: Compatible Devices Two-wire Smoke Detectors, UL Listed Model Identifier Table 3 Two-wire Smoke Detectors Use the two-wire detectors listed below. Four-wire Smoke Detectors, UL Listed FM Approved Releasing Devices Notification Appliances, UL Listed Appendix B: Compatible Devices Notification Appliances, UL Listed Table 6 Notification Appliances 42 Product Rated Voltage FWR DC Door Holders, UL Listed 24 VDC Relays, UL Listed Page Appendix C: NFPA Standard-Specific Requirements Minimum System Requirements Additional Requirements 46 Digital Alarm Communicator/Transmitter - Noti-Fire 911AC + TB3 Universal Digital Alarm Communicator - 411UDAC Local Energy Municipal Box FIRE + Remote Station Receiver - RS82-9 + + Page Appendix D: Testing & Maintenance Testing Inspection Alarm Test Maintenance Appendix D: Testing & Maintenance Troubleshooting 52 Table 9 Troubleshooting Table Symptom Problem Solution Index Numerics A B C J K L M N S T U V W Limited Warranty