System Sensor PDRP-1002 Series Remote Station Receiver

Remote Station Receiver - RS82-9 Appendix C: NFPA Standard-Specific Requirements

PDRP-1002 Instruction Manual PN 51135:B0 04/06/01 51

Remote Station Receiver - RS82-9

Using the 4XTM Transmitter Module for connection to a Fire•Lite RS82-9 Remote Station Receiver.

• Intended for connection to a polarity reversal circuit of a remote station receiving unit having

compatible ratings.

• All connections are power-limited and supervised with the exception of the reverse polarity loop.

• Supervision of the loop is the responsibility of the receiver.

Figure 27 RS82-9 Connections

TB1

TBL

Fire•Lite RS82-9

Remote Station

Receiver

MS44-rs82.cdr

4XTM Transmitter

Module

+ –

Remote

Trouble

Remote

Alarm

Contents

Main PDRP-1002 Heat detectors are designed to protect property, not life. While a fire alarm system may lower insurance rates, it is not a substitute for fire insurance! Fire Alarm System Limitations Several different sources of power can be con- nected to the fire alarm control panel. FCC Warning System Reacceptance Test after Software Changes. Adherence to the following will aid in problem-free installation with long-term reliability: Installation Precautions NFPA Standards Before proceeding, the installer should be familiar with the following documents. NFPA Standards Underwriters Laboratories Documents Other Table of Contents 1. Product Description 2. Installation 3. System Operation Appendix A: Secondary Power Calculations Appendix B: Compatible Devices Appendix C: NFPA Standard-Specific Requirements Appendix D: Testing & Maintenance 1. Product Description Overview Features Options Circuits Input Circuits Output circuits Front Panel Control Switches Suplemental Documentation Control Panel Figure 1 Control Panel DIP Switch Functions Options Transmitter Module - 4XTM Zone Relay Module - 4XZM Remote Annunciator - RZA-4X LED Interface Module - 4XLM Meter Module (Volts-Amps) - 4XMM Specifications 2. Installation Cabinet Mounting Removal of Circuit Board Mounting of Cabinet Attaching Conduit Reinstallation of Circuit Board Reinstall the printed circuit board as follows: Step Action Installing Optional Voltmeter/Ammeter Power Connections AC Connections Battery (DC) Connections Power-limited Wiring Requirements 2. Installation PDRP-1002 Instruction Manual PN 51135:B0 04/06/01 17 Power-limited Wiring Requirements J2 AMP TB5 MS44-BATconn.cdr AC Power Initiating Device Circuits Four-Wire Smoke Detector Connections Output Circuits Notification Appliance Circuits TB2 Releasing Circuits TB2 TB2 Alarm Relay Circuit Trouble Relay Circuit Powering External Devices TB1 TB2 Optional Modules Overview Installation - Upper Position Installation - Lower Position Setup and Configuration Page Page 2. Installation Setting Mode of Operation 28 Setting Mode of Operation Figure 19 DIP Switch Settings DIP Switch Functions Switch #1 - Cross Zone Select the desired mode of operation and set switch per appropriate column: OFF ON OFF ON * Abort timer will not operate when timer is set for No Delay. Zone Relay Module Configuration Power-Up Procedure Page 3. System Operation System Status LEDs Control Switches Zone Status LEDs Piezo Supervisory Service Zone Disable Last Event Recall Non-Silenceable Service Sprinkler Supervisory Tracking System Events Standby Condition Single Zone in Alarm (Cross Zone) Condition Both Zones in Alarm (Cross Zone) Condition Manual Discharge Station Alarm Condition Brownout Condition Page Appendix A: Secondary Power Calculations Standby Battery Requirements Calculating the Battery Capacity Appendix B: Compatible Devices Two-wire Smoke Detectors, UL Listed Model Identifier Table 3 Two-wire Smoke Detectors Use the two-wire detectors listed below. Four-wire Smoke Detectors, UL Listed FM Approved Releasing Devices Notification Appliances, UL Listed Appendix B: Compatible Devices Notification Appliances, UL Listed Table 6 Notification Appliances 44 Product Rated Voltage FWR DC Door Holders, UL Listed 24 VDC Relays, UL Listed Page Appendix C: NFPA Standard-Specific Requirements Minimum System Requirements Additional Requirements 48 Digital Alarm Communicator/Transmitter - Noti-Fire 911AC + TB3 Universal Digital Alarm Communicator - 411UDAC Local Energy Municipal Box FIRE + Remote Station Receiver - RS82-9 + + Page Appendix D: Testing & Maintenance Testing Inspection Alarm Test Maintenance Appendix D: Testing & Maintenance Troubleshooting 54 Table 9 Troubleshooting Table Symptom Problem Solution Index Numerics A B C G I J K L R S T U V Page Page Limited Warranty