4 This diagram shows the additional connections needed to expand from using up to four TANDBERG Precision HD cameras (see overleaf) to also include up to three TANDBERG WAVE II cameras (i.e. up to seven cameras in total). Connect Video Switch power supply as shown overleaf.
Note! | Camera 1 | Camera 2 | Camera 3 |
5 This diagram shows the connections needed to use a maximum of two analog sources equipped with component video outputs. Connection diagram uses Sony EVI-
HD1 cameras as example. System supports 1280X720p50, 1280X720p59,94, and 1280X720p60 only. For full VISCA control Sony
Mini
Start by connecting |
|
| Connect WAVE |
the Precision HD |
|
| |
cameras as shown |
|
| camera power |
|
| supply here. | |
overleaf. The |
|
| |
|
|
| |
connection shown | | | |
here comes in | |||
addition to the one | |
| |
| |||
overleaf! |
|
| |
|
|
| |
|
|
| |
|
|
Secondary chain
| Camera 1 |
|
| Control |
|
in |
| |
| ||
|
|
Camera 2
Control in
Connect camera power supply here.
The Codec must be equipped with | TANDBERG 6000 MXP Codec |
software version F6.1 or higher to |
|
support the use of the Video Switch. |
|
|
|
| 2. Aux | Video | 4. | PC | Audio in |
|
|
|
|
|
|
| PC Card | 3. | 3 | 4 |
| 1 | 2 |
| |
I |
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
| Ethernet | Camera | |
|
|
|
|
|
|
|
|
|
| ||
|
|
| Data | Video out |
| VCR |
|
|
| ||
|
|
|
|
|
|
|
| ||||
|
|
| 1. Single | 2. Single | 3. Dual | 1 | 2 | Mic.1 | Mic.2 |
|
|
O | DC in | USB | Audio out |
| Net | ||||||
TANDBERG 3000 MXP Codec
The Codec must be equipped with TANDBERG 6000 MXP Codec software version F6.1 or higher to
support the use of the Video Switch.
|
|
| 2. Aux | Video in | 4. VCR | PC | Audio in |
|
|
|
|
|
|
| PC Card | 3. Doc | 3 | 4 |
| 1 | 2 |
| |
I |
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
| Ethernet | Camera | |
|
|
|
|
|
|
|
|
|
| ||
|
|
| Data | Video out |
| VCR |
|
|
| ||
|
|
|
|
|
|
|
| ||||
|
|
| 1. Single | 2. Single | 3. Dual | 1 | 2 | Mic.1 | Mic.2 |
|
|
O | DC in | USB | Audio out |
| Net | ||||||
TANDBERG 3000 MXP Codec
To upgrade the software of the Precision HD camera, connect the camera directly to the main camera socket of the Codec (the socket that otherwise is used when connecting the Video Switch to the Codec).
Power the units and the upgrade will start automatically. The status will be shown on the video system’s monitor.
TANDBERG
1 |
|
| 8 |
| 1 | 8 |
| ||||||||||||
|
|
|
|
|
|
|
|
|
| RJ45 |
|
|
|
|
|
|
|
| RJ11 |
|
|
|
|
|
|
|
|
|
| Top |
|
|
|
|
|
|
|
| Top |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
| RJ45 |
|
|
|
|
|
|
|
| RJ11 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
| Front |
|
|
|
|
|
|
|
| Front |
1 |
| 8 |
| 1 | 6 |
| |||||||||||||
SONY Mini DIN | Precision HD RJ 11 | |||
1 DTR |
|
|
| 1 GND |
|
|
| ||
2 DSR |
|
| 2 Not Used | |
|
| |||
3 TXD | 3 TXD | |||
4 GND | 4 RXD | |||
5 RXD | 5 GND | |||
6 GND | 6 GND | |||
You may combine TANDBERG HD Precision cameras with analog sources equipped with component video outputs. Just add them to the chain of cameras in the diagram shown overleaf, but make sure the added sources appear after the TANDBERG HD Precision cameras in the chain (i.e. after camera 4 in the diagram overleaf).
Consequently, up to four TANDBERG HD Precision cameras may be combined with up to two analog component video sources and up to three TANDBERG WAVE II cameras, bringing the maximum number of video sources (which in many cases will be all cameras) up to nine!
| 1 | 2 |
|
| 2 | 1 |
|
RJ45 | 3 | 3 | RJ11 |
6 | 4 | ||
| 7 | 5 |
|
|
|
|
|
SONY Part Numbers: | ||
| SONY part number RC893 | SONY part number RC815 |
Page 2 of 6 | 116467.05 |
