GB
TAKING WEIGHT AND BODY FAT READINGS
GB
PROGRAMMING THE GUEST MODE
1 | 2 | 3 | 4 |
AC T I V I T Y
L E V E L
D C I
1. Select Personal Key and Step On
Using your toe, tap your
The unit will beep again and the display will show "0.0". Now step onto the platform.
Note: If you step onto the platform before “0.0” appears the display will show “Err” and you will not obtain a reading. Furthermore, if you do not step onto the measuring platform within about 60 seconds after “0.0” appears, the power is
The Guest mode allows you to use the monitor without losing the information already assigned to a Personal Key.
To programme the Guest mode, use the Down button marked to turn on the power. Then follow steps 3 through 5 in “Setting and Storing Data” (p.5). The unit will beep twice and the display will show “0.0”. Step onto the platform. Next follow the directions for “Get Your Reading” (p.6).
Note : If you step onto the platform before “0.0” appears the display will show “Err” and you will not obtain a reading.
AC T I V I T Y L E V E L
D C I
TAKING WEIGHT MEASUREMENT ONLY
Select
2. Get Your Readings |
Your weight will be shown first. |
Continue to stand on the platform. |
AC T I V I T Y |
L E V E L |
D C I |
"54321" will appear on the display and disappear one by one from right to left. |
Your body fat peacentage(%FAT) and Body Fat Range will appear on the |
Using your toe, tap the
1 | 2 |
3
4
| display screen. |
AC T I V I T Y | The display will then flash your weight %FAT and DCI alternately 3 times. |
L E V E L | |
D C I |
Note:Do not step off until Body Fat % is shown.
AC T I V I T Y |
L E V E L |
D C I |
UNDERSTANDING YOUR READING
TROUBLESHOOTING
If the following problems occur …then…
•A wrong weight format appears followed by kg, lb, or
Refer to “Switching the Weight Mode” on p.4.
•”Lo” appears on the display, or all the data appears and immediately
disappears.
Batteries are low. When this message appears, be sure to replace the batteries immediately, since weak batteries will affect the accuracy of your measurements. Change all the batteries at the same time with new
Note: Your settings will not be erased from the memory when you remove the batteries.
•”Err” appears while measuring.
Under Healthy Over Obese
*Note: If you select Athlete mode, the unit will not display the Healthy Range Indicator. Athletes may have a lower body fat range based on their particular sport or activity.
(Range of user age is between
Healthy Range Indicator (Standard Adults only*)
Your body fat monitor/scale automatically compares your body fat reading to the Healthy Body Fat Range chart.
Following your body fat percentage reading, a black bar will flash along the bottom of the display, identifying where you fall within the Body Fat Ranges for your age and gender. For example, if the squares appear above (0) area your range is within the Healthy Range – if they appear over
: Underfat; below the healthy body fat range. Increased risk for health problems. |
(0): Healthy; within the healthy body fat percentage range for your age/gender.
(+): Overfat; above the healthy range. Increased risk for health problems. (++) : Obese; high above the healthy body fat range. Greatly increased risk
of
Please stand on the platform keeping movement to a minimum.
The unit cannot accurately measure your weight if it detects movement.
•The Body Fat Percentage measurement does not appear or
after the weight is measured.
Your personal data has not been programmed. Follow the steps on p.5.
Make sure socks or stockings are removed, and the soles of your feet are clean and properly aligned with the guides on the measuring platform.
•”OL” appears while measuring.
•”Err FAT%” appears while measuring.
•”Err kcal(cal)” appears.
The DCI (Daily Calorie Intake) is more than 9999kcal (for USA 9999cal).
6
7
