10.0: SERVICING 
10.1: CABINET FINISH
To remove marks and scuffs use a soft brush. If necessary, a little warm water and detergent can be used but under no circumstances use a solvent or abrasive cleaner.
10.2: DRIVER REMOVAL
Lay the cabinet on its back. Remove the ten hexagonal screws and set aside. Ease the driver from the front of the cabinet taking care not to mark the front surface. Remove the driver, note the polarity of the internal connections and disconnect the internal wiring. Take care not to damage the moving parts of the LF driver. To refit the driver, connect the cables from the crossover to the LF terminals. Fit the driver into the mounting hole, making sure that the internal connecting cables are not trapped or able to touch the LF cone. Fasten the screws finger tight and then progressively tighten them down with the appropriate Allen key. Repeat the same procedure for the HF driver.
10.3: AMPLIFIER
A fuse is located just under the mains input (fig 1). Replacement is simple and a spare fuse is provided inside the fuse housing itself. Always use the correctly rated fuse, as indicated on the silk
In case of any malfunction of the unit, the first thing to check should be the input connection, more especially if the source has unbalanced outputs (see "Connecting your speakers" section) as improper connection can result in significant level reduction and affect the response.
10.4: LIST OF SPARE PARTS
DESCRIPTION | REVEAL 6D (PART NO) | REVEAL 8D (PART NO) | REVEAL 66D (PART NO) | |
|
|
|
|
|
Driver Kit | Type 1603 | Type 2076 | Type 1603 | |
|
|
|
|
|
High Frequency Unit | Type 0294 – 7900 0891B | Type 0294 – 7900 0891B | Type 0294 | – 7900 0891B |
|
|
|
| |
Amplifier Complete | 7300 0932 (230V) | 7300 0933 (230V) | 7300 0934 (230V) | |
|
|
|
| |
Amplifier Complete | 7300 1026 (110V) | 7300 1027 (110V) | 7300 1028 (110V) | |
|
|
|
| |
Filter Board Assembly | 7600 1550 | 7600 1551 | 7600 1552 | |
|
|
|
| |
Power Board Assembly | 7600 1556 | 7600 1557 | 7600 1557 | |
|
|
|
| |
Digital I/O Board Assembly | 7600 1558 | 7600 1558 | 7600 1558 | |
|
|
|
| |
Features Board Assembly | 7600 1409 | 7600 1409 | 7600 1409 | |
|
|
|
| |
Transformer | 3212 0132 | 3212 0133 | 3212 0132 | |
|
|
|
|
|
Passive Crossover |
|
| Type 1509 | – 7300 1044 |
|
|
|
|
|
11.0: WARRANTY
NO MAINTENANCE OF THE REVEAL 6D, 8D & 66D MONITORS IS NECESSARY.
All components are guaranteed for a period of one year from the date of manufacture, subject to the absence of, or evidence of, misuse, overload or accidental damage.
For further information please contact your dealer or the distributor in your country.
If you cannot locate your distributor please contact:
Customer Services, Tannoy Ltd., Coatbridge, Strathclyde, ML5 4TF, Scotland
Telephone: 01236 420199 (UK) +44 1236 420199 (International)
Fax: 01236 428230 (UK) +44 1236 428230 (International)
Internet: http://www.tannoy.com
DO NOT SHIP ANY PRODUCT TO TANNOY WITHOUT PREVIOUS AUTHORISATION
This warranty in no way affects your statutory rights.
12.0: DECLARATION OF CONFORMITY
The following apparatus is/are manufactured in China by Tannoy Ltd of Rosehall Industrial Estate, Coatbridge, Scotland, ML5 4TF. The following equipment is marked with the CE label and conform(s) to the protection requirements of the European Electromagnetic Compatibility Standards and Directives. The apparatus is designed and constructed such that electromagnetic disturbances generated do not exceed levels allowing radio and telecommunications equipment and other apparatus to operate as intended, and, the apparatus has an adequate level of intrinsic immunity to electromagnetic disturbance to enable operation as specified and intended.
Details of the Apparatus: Reveal 6D Studio Monitor
Reveal 8D Studio Monitor
Reveal 66D Studio Monitor
The equipment listed above is covered by this certificate and marked with the
EN 60065 | Safety requirements for mains operated electronic and related |
(IEC 60065) | apparatus for household and similar general use |
EN | Product family standard for audio, video, |
| for professional use. Part 1: Emission. |
EN | Product family standard for audio, video, |
| for professional use. Part 2: Immunity. |
With reference to regulations in following directives: 73/23/EEC, 89/336/EEC
Signed:
Position: | Technical Director |
Date: | 1 March 2005 |
For Tannoy Ltd |
|
22 | 23 |
