Tannoy 6D 66D & 8D manual Way DIP Switch Bank 4+4+2+4+6

Low Mid Contour Frequency: A shelving filter can be set to the flat anechoic response or set to shelve at frequencies of 800Hz, 400Hz, or 200Hz in combination with the low mid contour amplitude (below) to correct half space (pi/2), quarter space (pi/4) and very difficult close field boundary conditions (pi/8 space).

Low Mid Contour: a shelving filter can be set to a flat anechoic response or to -2dB, -4dB, -6dB or -8dB in combination with the low mid contour frequency (above) to correct mid, near and close field listening positions compared with free space, far field conditions.

Figures 3, 4 and 5 below show the range of amplitude settings at 800Hz, 400Hz and 200Hz and the DIP switch settings. DIPs 5 to 8 (inclusive) control the amplitude responses and switches 9 and 10 control the frequency at which the shelving starts. All other DIPs are shown in the 'Flat' position.

Baffle Step Effect: Both low mid frequency and low mid contour are used together to correct for the baffle step effect. the baffle step effect is a well known property of speakers and is caused by a change in air load on the moving diaphragm at a frequency dependant on the effective size of the baffle or cabinet frontal area compared with the wavelength of the sound being reproduced. Most speakers are designed to have a flat amplitude and phase response over the audio band in anechoic or 'free field' conditions where there are no boundary walls close to the bass drive unit. When the speaker is placed against a wall, in a corner, on a mixing console or on a table adjacent to a PC editor the wall boundaries effectively increase the baffle size. This produces a boost in the frequency band around 100 to 800 Hz depending on the effective size and proximity of the boundary surfaces, the size of the bass driver and the distance of the listener from the source.

More at: Olson, H. F. "Direct Radiator Loudspeaker Enclosures" Journal of the Audio Engineering Society Vol. 17, No. 1, 1969 October, pp.22-29

There are many more references to these effects by searching the web for 'Baffle Step Effect'.

Diagramatic View of EQ Dip Switches: Baffle Step Filters, Low Mids, 800Hz

20 way DIP Switch Bank (4+4+2+4+6) LF EQ Low Mids Hz Up Mid Highs

+10dB
				1 1 1 0	1 1 1 0	0 0	0 0 0 0	0 0 0 0 0 0
0dB re 2.8v
@ 1 metre
-10dB
				1 1 1 0	0 1 1 0	0 0	0 0 0 0	0 0 0 0 0 0
				1 1 1 0	0 0 1 0	0 0	0 0 0 0	0 0 0 0 0 0
				1 1 1 0	0 0 0 0	0 0	0 0 0 0	0 0 0 0 0 0
				1 1 1 0	0 0 0 1	0 0	0 0 0 0	0 0 0 0 0 0
10Hz	20Hz	50Hz	100Hz	200Hz	500Hz	1Khz	2kHz	5kHz	10kHz	20kHz

Fig. 3. DIP switches 5 to 8 control amplitude, 9 & 10 control frequency - set here to 800Hz. All other DIPs set to 'flat'.

Diagramatic View of EQ Dip Switches: Baffle Step Filters, Low Mids, 400Hz

20 way DIP Switch Bank (4+4+2+4+6) LF EQ Low Mids Hz Up Mid Highs

+10dB
				1 1 1 0	1 1 1 0	0 0	0 0 0 0	0 0 0 0 0 0
0dB re 2.8v
@ 1 metre
-10dB
				1 1 1 0	0 1 1 0	1 0	0 0 0 0	0 0 0 0 0 0
				1 1 1 0	0 0 1 0	1 0	0 0 0 0	0 0 0 0 0 0
				1 1 1 0	0 0 0 0	1 0	0 0 0 0	0 0 0 0 0 0
				1 1 1 0	0 0 0 1	1 0	0 0 0 0	0 0 0 0 0 0
10Hz	20Hz	50Hz	100Hz	200Hz	500Hz	1Khz	2kHz	5kHz	10kHz	20kHz

Fig. 4. DIP switches 5 to 8 control amplitude, 9 & 10 control frequency - set here to 400Hz. All other DIPs set to 'flat'.

Diagramatic View of EQ Dip Switches: Baffle Step Filters, Low Mids, 200Hz

20 way DIP Switch Bank (4+4+2+4+6) LF EQ Low Mids Hz Up Mid Highs

+10dB
				1 1 1 0	1 1 1 0	0 0	0 0 0 0	0 0 0 0 0 0
0dB re 2.8v
@ 1 metre
-10dB
				1 1 1 0	0 1 1 0	1 1	0 0 0 0	0 0 0 0 0 0
				1 1 1 0	0 0 1 0	1 1	0 0 0 0	0 0 0 0 0 0
				1 1 1 0	0 0 0 0	1 1	0 0 0 0	0 0 0 0 0 0
				1 1 1 0	0 0 0 1	1 1	0 0 0 0	0 0 0 0 0 0
10Hz	20Hz	50Hz	100Hz	200Hz	500Hz	1Khz	2kHz	5kHz	10kHz	20kHz

Fig. 5. DIP switches 5 to 8 control amplitude, 9 & 10 control frequency - set here to 200Hz. All other DIPs set to 'flat'.

8 9