AMPLIFIER MATCHING

Consult the Technical Specification section for the acceptable range of amplifier powers. The high peak power handling of Tannoy loudspeakers permits the responsible use with more powerful amplifiers.

As with all loudspeakers, power handling is a function of voice coil thermal capacity. Take care to avoid overdriving any amplifier, as the resulting distortion, or ‘clipping’, can damage the loudspeaker if allowed to continue for an extended period. Generally a higher power amplifier, running free of distortion is safer than a lower power amplifier being driven hard, and will also sound better.

INSTALLATION

If desired, the grille and baffle panel may be painted to match the surrounding décor. Several thin coats of paint will provide a better finish than one overly thick coat.

∙￿ When painting the baffle, carefully mask off the driver assembly, ensuring that paint does not come into contact with the cone and roll surround.

∙￿ Paint the grille, leaving the acoustically transparent foam in place on the reverse side. Remove and discard original foam, replacing with the spare sheet supplied. It is important that this is bonded over it’s entire area, using a suitable spray adhesive, to avoid audible resonance.

Using the supplied template, cut the mounting aperture in the ceiling and place the C ring in position, to spread the weight of the clamps on the ceiling. Beware of hidden obstructions and electrical wiring. Always use a good quality speaker cable, and allow enough spare for the loudspeaker to be installed or removed easily. Connect to the two spring terminals, being careful to observe polarity, positive to positive and negative to negative.

Position the loudspeaker in the aperture and tighten the 3 screws which engage the clamping mechanism (Figure 1). WARNING: do not over tighten.

If the speaker has to be removed, loosen the 3 screws, ensuring the clamps are fully retracted.

Figure 1: Fitment in Ceiling

GRILLE FITTING AND REMOVAL

Before fitting the grille, the HF level control on the baffle should be set to the desired position, according to the acoustics of the environment.

The grille is a tight fit, and should be located by applying even pressure around the circumference. To avoid indentation, do not press the centre of the grille.

If the grille has to be removed, use a firm piece of wire, such as an opened up paper clip, inserted through the mesh. Work around the outside of the grille, to gently prise it off.

3

Page 2 Page 4
Page 3
Image 3
Tannoy ic6 DC owner manual Amplifier Matching, Installation, Grille Fitting and Removal
Page 2 Page 4

ic6 DC specifications

The Tannoy IC6 DC is a remarkable in-ceiling speaker that epitomizes high-quality audio engineering suited for both residential and commercial applications. Designed to blend seamlessly with any interior, the IC6 DC is an ideal choice for those seeking professional-grade acoustic performance without compromising aesthetics.

One of the standout features of the IC6 DC is its Dual Concentric technology. This innovative design positions the high-frequency driver within the low-frequency driver, allowing for a point-source sound. This configuration facilitates better phase coherence and wider dispersion of sound, ensuring an immersive listening experience across a broad area. As a result, listeners can enjoy an arguably better sonic performance than typical speakers, making them perfect for home theaters, multi-room audio systems, or any environment where sound quality is paramount.

The IC6 DC also boasts a 6.5-inch polypropylenewoofer, specifically designed to deliver deep, punchy bass while ensuring clarity across the audio spectrum. The tweeter, which is a 1-inch soft dome, provides smooth high frequencies, enabling clear dialogue and detailed musical nuances. These drivers work harmoniously together to provide a balanced sound that can fill the room with well-defined audio.

Installation is straightforward due to the IC6 DC's slim profile and light weight. Its low-profile design allows it to fit seamlessly into ceilings without obstructing the visual appeal of a room. The speaker comes equipped with an easy-to-use mounting system, which includes a dog-leg clamp mechanism, ensuring a secure fit in both new constructions and retrofit installations.

Moreover, Tannoy’s commitment to quality extends to the build materials of the IC6 DC. The speaker features a robust grill that is both paintable and corrosion-resistant, allowing customization to match any décor while ensuring durability. The enclosure is designed to minimize vibrations and sound distortion, further enhancing the acoustic performance.

In addition to its exceptional sound quality and aesthetics, the Tannoy IC6 DC is designed with reliability in mind, producing consistent audio performance over the lifespan of the product. This speaker is an excellent choice for those who seek a combination of elegance and high-fidelity audio, making it a valuable addition to any sound system. Whether utilized for a home entertainment setup or commercial audio applications, the Tannoy IC6 DC stands out as a premier choice for discerning audiophiles.
Top Page Image Contents