Changing Oven Light |
|
| Be sure the range is unplugged and all parts are COOL before | ||
|
| ||||
(some models) | replacing the surface or oven lights. Wear a | ||||
|
| against possible broken glass. | |||
|
| To Change the Oven Light (some models) | |||
|
| On some models, the oven light automatically turns on when the door is | |||
|
| opened. Some models have a switch located on the control panel to turn on | |||
|
| the light. The oven light is located at the rear of the oven. | |||
|
| To replace the oven light: | |||
|
| 1. Turn electrical power off at the main source or unplug the range. | |||
|
| 2. Replace bulb with a new 40 watt appliance bulb. | |||
|
| 3. Turn power back on again at the main source (or plug the range back in). | |||
|
| 4. The clock(if equipped) will then need to be reset. To reset, see Setting the | |||
|
| Clock and Minute Timer in this Owner's Guide. | |||
|
|
|
|
|
|
| Avoid Service Checklist | Before you call for service, review this list. It may save you time and expense. | |||
|
| ||||
|
| The list includes common occurrences that are not the result of defective | |||
|
| workmanship or materials in this appliance. | |||
| OCCURRENCE | POSSIBLE CAUSE/SOLUTION | |||
|
|
|
|
| |
| Range is not level. | Poor installation. Place oven rack in center of oven. Place a level on the oven | |||
|
| rack. Adjust leveling legs at base of range until the rack is level. When oven is | |||
|
| level, cooktop may not appear to be level with countertop. | |||
|
|
|
|
|
|
|
| Weak, unstable floor. Be sure floor is level and can adequately support range. | |||
|
| Contact a carpenter to correct sagging or sloping floor. | |||
|
|
|
|
|
|
|
| Kitchen cabinet misalignment may make range appear to be unlevel. Be sure | |||
|
| cabinets are square and have sufficient room for range clearance. | |||
|
|
|
|
| |
| Cannot move appliance easily. | Cabinets not square or are built in too tight. Contact a cabinet maker to correct | |||
| Appliance must be accessible for | the problem. | |||
| service. |
|
|
|
|
|
| Contact builder or installer to make appliance accessible. | |||
|
|
|
|
|
|
|
| Carpeting interferes with range. Provide sufficient space so range can be lifted | |||
|
| over carpet. | |||
|
|
|
|
|
|
|
| Gas line is | |||
|
| appliance connector installed. | |||
|
|
|
|
| |
| Surface burners do not light. | Surface Control knob has not been completely turned to LITE. Push in and turn | |||
|
| the Surface Control knob to LITE until burner ignites and then turn control to | |||
|
| desired flame size. | |||
|
|
|
|
|
|
|
| Burner ports are clogged. With the burner off, use a | |||
|
| to clean ports. See "Surface Burners" in the cleaning chart under General | |||
|
| Cleaning for additional cleaning instructions. | |||
|
|
|
|
|
|
|
| Range power cord is disconnected from outlet. Be sure cord is securely plugged | |||
|
| into the outlet. | |||
|
|
|
|
|
|
|
| Electric power outage. Burners can be lit manually. See Setting Surface | |||
|
| Controls in this Owner's Guide. | |||
|
|
|
|
|
|
14