IF-AE8 Digital Audio Converter

CONSUMER IEC-60958 TYPE II format. The elec- trical characteristics of the output connectors remain the same, regardless of the data format selected.

6Fs RATE CONVERT switch and indicators

This switch provides two settings: THRU-1and

CONVERT.

the clock source for the converted signal. The DIGITAL I/O (TDIF-1)9 cannot be used as the clock source for conversion, though both it and the

DIGITAL I/O (AES/EBU) OUTPUTS (1/2, 3/4, 5/6, 7/8) 7 can be the destination.

NOTE

When the switch is set to THRU-1, the input signals (selected using the DIGITAL OUT 4 switch) will be output from the AES/EBU output connectors at the same frequency.

When the switch is set to CONVERT, the input sig- nals will be output at the sampling frequency of the clock source selected with the CLOCK switch 3.

Note that any of the DIGITAL I/O (AES/EBU) INPUTS (1/2, 3/4, 5/6, 7/8) 8 may be selected as

The AES/EBU unit which provides this clock source may be different from the unit which provides either the input or the output signals. You must, however, make sure that word clock synchronization is correctly carried out.

2 Rear panel

7DIGITAL I/O (AES/EBU) OUTPUTS (1/2, 3/4, 5/6, 7/8)

These balanced connectors output digital audio data in AES3-1992 professional or in consumer format, depending on the selection made with the DIGITAL OUT FORMAT switch 5.

The content of the data depends on the setting of the DIGITAL OUT switch 4.

The sampling frequency of the output data depends on the setting of the Fs RATE CONVERT switch 6, and the currently-selected clock source 3.

8DIGITAL I/O (AES/EBU) INPUTS (1/2, 3/4, 5/6, 7/8)

These balanced connectors accept digital audio data in AES3-1992 format.

The signal received at any of these connectors may be selected as the clock source for the IF-AE8 using the CLOCK switch 3

9DIGITAL I/O (TDIF-1)

Use this connector to connect a suitably-equipped TDIF-1 digital audio unit (e.g. a DTRS recorder or a TASCAM digital mixing console).

The signals received at this connector may be selected as the word clock source using the CLOCK switch 3.

WARNING

Note that you should always use genuine TASCAM cables, or cables which have been approved for use with TDIF-1 interfaces by

TASCAM.

Although these cables appear similar to cer- tain types of computer cables and use similar connectors, the cables themselves are very different, and the different electrical character- istics of the cables can cause damage to the equipment connected with the wrong cables.

If the use of cables other than TASCAM cables causes or results in damage, the war- ranty is voided.

AWORD SYNC IN

The BNC connector accepts a word clock signal from an external source.

It may be selected as the word clock source for the IF-AE8 using the CLOCK switch 3.

TASCAM IF-AE8 5

Page 4 Page 6
Page 5
Image 5
Tascam IF-AE8 owner manual Rear panel, Digital I/O TDIF-1, Word Sync
Page 4 Page 6

IF-AE8 specifications

The Tascam IF-AE8 is a powerful audio interface specifically designed for use with Tascam's series of digital mixers and recording systems. Its versatility and high-quality performance make it an ideal choice for audio engineers and musicians who demand exceptional sound quality and flexible connectivity options.

One of the standout features of the IF-AE8 is its capability to provide eight channels of analog input and output. This allows users to connect a wide variety of audio sources, including microphones, instruments, and line-level devices, providing the flexibility needed for complex recording setups. The interface is equipped with high-quality ADAT and AES/EBU digital outputs, allowing for seamless integration into digital recording environments.

The IF-AE8 employs advanced conversion technology that ensures pristine audio fidelity. With high-resolution 24-bit/192 kHz digital conversion, users can expect rich detail and clarity in their recordings. This is particularly advantageous in professional settings where audio quality is paramount. Furthermore, the unit features a dynamic range that minimizes distortion, resulting in clean and powerful audio capture.

Another defining characteristic of the IF-AE8 is its intuitive design, which simplifies operation for users at all levels of experience. The interface includes a clear LED display that provides real-time feedback on input levels and signal processing, making it easy to monitor audio levels during recording or mixing sessions. Additionally, the unit is compact and rugged, making it suitable for both studio and live applications.

The IF-AE8 also supports the use of real-time DSP processing, enabling users to apply various effects and enhancements without the need for external software plugins. This functionality can significantly streamline the recording process and improve the overall workflow in a studio environment.

Compatibility is yet another key aspect of the Tascam IF-AE8. It integrates seamlessly with Tascam’s range of digital mixers, like the Model 24 and Model 16, as well as other audio recording systems. This versatility ensures that users can expand their existing setups without hassle.

In summary, the Tascam IF-AE8 is a robust audio interface that combines excellent sound quality, user-friendly features, and flexible connectivity options. Whether for recording music, sound design, or live sound applications, the IF-AE8 stands out as a reliable and effective solution for professional audio needs.
Top Page Image Contents