Advanced Data Sheet: Veta® iHA48060A012V*, 1.2V/60A Output Half Brick
Electrical Data (continued):
Operating at Tc = 25°C unless otherwise specified
Output Characteristic | Min |
| Typ |
| Max |
|
| Unit |
| Notes & Conditions |
Output Voltage Initial Setpoint | 1.18 |
| 1.2 |
| 1.22 |
|
| Vdc |
| Vin=Vin,nom; Io=Io,max |
|
|
|
|
|
|
|
|
|
|
|
Output Voltage Tolerance | 1.16 |
|
| 1.24 |
|
| Vdc |
| Over all rated input voltage, load, and | |
|
|
|
|
|
|
|
|
|
| temperature conditions to end of life |
|
|
|
|
|
|
|
|
|
| |
Efficiency |
| 83 |
|
| % |
| Vin=Vin,nom; Io=Io,max | |||
|
|
|
|
|
|
|
|
|
|
|
Line Regulation |
| 1 |
| 2* |
|
| mV |
| Vin=Vin,min to Vin,max | |
|
|
|
|
|
|
|
|
|
|
|
Load Regulation |
| 4 |
| 6* |
|
| mV |
| Io=Io,min to Io,max | |
|
|
|
|
|
|
|
|
|
|
|
Temperature Regulation |
| 10 |
| 15* |
|
| mV |
| Tc=Tc,min to Tc,max | |
|
|
|
|
|
|
|
|
|
|
|
Output Current | 0 |
|
| 60 |
|
| A |
| At loads less than 25% of Io,max the module | |
|
|
|
|
|
|
|
|
|
| will continue to regulate the output voltage, |
|
|
|
|
|
|
|
|
|
| but the output ripple may increase |
|
|
|
|
|
|
|
|
|
|
|
Output Current Limiting Threshold | 61 |
| 76 |
| 90 |
|
| A |
| Vo = 0.9*Vo,nom, Tc<Tc,max |
|
|
|
|
|
|
|
|
|
|
|
Short Circuit Current |
| 76 |
|
|
| A |
| Vo = 0.25V | ||
|
|
|
|
|
|
|
|
|
|
|
Output Ripple and Noise Voltage |
| 55 |
| 60 |
|
| mVpp |
| Measured across one 47uF, one 1uF and | |
|
|
|
|
|
|
|
|
|
| one 0.1uF ceramic capacitors – see |
|
|
|
|
|
|
|
|
|
| input/output ripple measurement figure; BW = |
|
| 15 |
| 18 |
|
| mVrms |
| ||
|
|
|
|
|
| 20MHz | ||||
|
|
|
|
|
|
|
|
|
|
|
Output Voltage Adjustment Range | 50 |
|
| 110 |
|
| %Vo,nom |
|
| |
|
|
|
|
|
|
|
|
|
|
|
Output Voltage Sense Range |
|
| 10 |
|
| %Vo,nom |
|
| ||
|
|
|
|
|
|
|
|
|
|
|
Dynamic Response: |
|
|
|
|
|
|
|
|
| di/dt = 0.1A/uS, Vin=Vin,nom; load step from |
Recovery Time |
| 0.25 |
|
|
| mS |
| 50% to 75% of Io,max | ||
Transient Voltage |
| 35 |
|
|
| mV |
| For applications with large step load changes | ||
|
|
|
|
|
|
|
|
|
| and/or high di/dt load changes, please |
|
|
|
|
|
|
|
|
|
| contact TDK Innoveta for support. |
|
|
|
|
|
|
|
|
|
|
|
Output Voltage Overshoot during startup |
| 0 |
|
|
| mV |
| Io=Io,max | ||
|
|
|
|
|
|
|
|
|
|
|
Switching Frequency |
| 240 |
|
|
| kHz |
| Fixed | ||
|
|
|
|
|
|
|
|
|
|
|
Output Over Voltage Protection |
| 1.5 |
|
|
| V |
| All line, load, and temperature conditions | ||
|
|
|
|
|
|
|
|
|
|
|
External Load Capacitance | 50 |
|
| 60000** |
|
| uF |
|
| |
|
|
|
|
|
|
|
|
|
|
|
Isolation Capacitance |
| 2000 |
|
|
| pF |
| All line, load, and temperature conditions | ||
|
|
|
|
|
|
|
|
|
|
|
Isolation Resistance | 10 |
|
|
|
| MΩ |
| All line, load, and temperature conditions | ||
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
Vref |
|
| 1.225 |
|
|
|
| V |
| Required for trim calculation |
|
|
|
|
|
|
|
|
|
|
|
*Engineering Estimate
**Contact TDK Innoveta for applications that require additional capacitance
Caution: The power modules are not internally fused. An external input line normal blow fuse with a maximum value of 20A is required, see the Safety Considerations section of the data sheet.
©2007 TDK Innoveta Inc. | ' (877) |
iHA Datasheet 040207 | 6/16 |
| |
|
|
