Techko S082K, S082X manual Battery Installation, Entering Code to ARM and Disarm

TEMPLATE

MODE S082X

SCREW HOLE

SCREW HOLE

CHANGING A SECURITY CODE TO A NEW CODE

1.Enter the old security code number.

2.Press the*	/CODE	button.
3.Enter the new code(1 to 12 digits), (S082KA is 1 to 7).
4.Press the	*/CODE	button, the unit will beepo nce to

confirm your new code has been entered.

SENSORS

ON DOOR

SENSORS

ON WINDOW

Fig.2

MOUNTING

SELECT A MOUNTING LOCATION

NOTE: Before mounting the unit be sure to read theS AFETY TIPSs ection at the beginning of the manual.

1.Apply double sided tape (included) to back of sensor switch pair. Mount sensor without wire to the door or window. Mount the sensors with wire to the door or window frame. (Fig.2) Be sure the magnetic sensors are mounted no further than a 1/4f rom each other.

2.Using the mounting plate as template, mark the screw hole locations and drill two 1/4h oles. Tap the provided screw anchor into place. (Fig.3)

3.Secure the mounting plate to the wall with the screws provided.

4.Snap the alarm unit into place on the mounting plate.

AFFIX SELF	AFFIX SELF
ADHESIVE	ADHESIVE
TAPE HERE	TAPE HERE
	KEY HOLE
	FOR WALL
	MOUNTING
	Fig.3

INSTALLATION

BATTERY INSTALLATION

1.Remove screws from battery compartment located on the bottom of the unit .(Fig.1)

2.Install 3 AAA batteries / 9V battery. (Not included).

NOTE: When the batteries are installed for the first time or are replaced the security code will automatically default

back to

0

(S082KA factory code is

5

) and the LED indicator

will illuminate. This unit will also be in

the ARM

mode. After

installing the battery to disarm the unit press

0

/

5 and

the

#ON/OFF

button. A short Confirming

beep

will sound

and the LED light will go out to verify the unit has been

disarmed.

ENTERING CODE TO ARM AND DISARM

NOTE: The default for the security code is

0

(S082KA default

is

5 ). When the battery is replaced the unit will reset to the

factory set code

0

/

5 .

1.Press the

0 /

5

button or the code that is currently in

memory.(New battery default is 0

/

5

). If there is an

existing code use that in place of the

0

/

5 .

2.Press the

#ON/OFF

button, a confirming

beep

should be

heard.

3.If the wrong security code is entered there will be two tone

beep

, this is different from the single beep confirmation.

4.When the unit is armed the ARM

LED will illuminate.

3x1.5V AAA 1x9V 6F22

PROGRAMMING

A SECURITY CODE

NOTE: The programmable security code can be a 1 to 12 digit code. (S082KA is 1 to 7 digits). Shorter codes such as 1 to 4 digits are easy to remember, long codes can provide greater safety. DO NOT INCLUDE A 0 IN YOUR CODE (S082X). DO NOT INCLUDE A 5 IN YOUR CODE (S082KA).

TO PROGRAM A SECURITY CODE AFTER

BATTERY INSTALLATION

1.Press the	0 (S082KA is 5 ) button.
2.Press the	*/CODE	button.
3.Enter the new code (1 to 12 digits), (S082KA is 1 to 7).
4.Press the	*/CODE	button, the unit will beep once to confirm

your new code has been entered.

INTRODUCTION

Congratulations on your purchase of the TECHKO model S082X/S082KA.The MAGNET GUARD provides detection of unwanted intruders in your home by detecting entry. This unit can be mounted on any door or window. Arming and disarming of the unit is done by entering a security

code on the keypad.

FEATURES

*Requires no wiring or special installation.

*Built-in 110db (S082KA is 115db) alarm siren.

*Up to 12 (S082KA 7 digits) digits programmable security codes.

*Alarm / chime switchable mode.

*5-10 seconds entry alarm delay with alert beep tone.

*Magnetic sensor detects entry.

*Direct access PANIC button.

*4.5V (3 1.5V AAA size) alkaline battery operation (S082KA uses 9V battery) (Not included).

*Optional AC adaptor power operation for S082KA.

*2 warning stickers for possible points of entry.

SAFETY TIPS

1.Read all installation and operation instructions carefully before using.

2.Alarm siren is very loud, never put the unit close to your ear.

3.Avoid rough handling.

4.Do not install alarm where it will be exposed directly to sunlight or high humidity.

5.The unit can provide valuable protection for your home and property if utilized properly. However, this unit can not guarantee compete protection against burglary

or robbery. Therefore, TECHKO cannot be held liable for loss or damage which could occur.

6.Keep this manual in a convenient location for future reference.