Technicolor - Thomson 8900NET - page 55

8900NET Instruction Manual 55

Service

3. Is the correct IP Address/URL being used to address the frame?

If a Domain Name is being used to address the frame, try to connect

using the frame IP Address instead.

The Domain Name may not be properly assigned in the local Domain

Name Server or in the workstation’s host ﬁle.

The Domain Name Server may not be available to the workstation.

Check that the 8900NET module has been properly conﬁgured.

a. Is the correct IP Address or URL being addressed in the web

browser?

b. Was the 8900NET module conﬁgured over the serial connection

with the SETUP command?

c. Has the 8900NET module been assigned the correct IP Address in

SETUP (re-run setup over the serial connection)?

d. Is the workstation in the same subnet as the frame? If not:

Has the 8900NET module been assigned the correct Default

Routing Address?

Has the 8900NET module been assigned the correct Subnet Mask?

e. Has the 8900NET module been rebooted since new IP Address,

Default Routing, or Subnet Mask were assigned or changed?

4. Check if the frame web pages can be opened from a different

workstation on the network.

5. Is the subject workstation physically connected to the network?

6. Check that the workstation and browser have been properly

conﬁgured.

a. Can the frame be opened from a different workstation?

b. Has the workstation been assigned a proper IP Address?

c. Has the workstation been assigned a Gateway Address?

d. Is the browser conﬁgured to connect to the correct port?

Is it attempting to connect through a modem when it should be con-

necting through a network interface module?

Some laptop have two separate network ports, one for stand-alone

operation, and the other for operation with a docking station. Is the

correct port being used?

Contents

Main Contacting Grass Valley Grass Valley Web Site Contents 8900NET Network Interface Module Preface Appendix Index Preface About This Manual Page 8900NET Network Interface Module 8900NET Features Introduction Remote Control Panel Basic Network Design Installation Module Placement in the Gecko 8900 Frame Page Cabling RS-232 Communication Port Cable Frame Alarm Page 8900NET Instruction Manual 13 If the PC uses a 25-pin RS-232 connector, use a cable adapter as shown in Figure 7. The 25-pin adaptor is available from Grass Valley as part of cable kit model 8900CAB. Ethernet Cable Point-to-Point Connection Local Area Network (LAN) Connection Figure 9 illustrates the cable connection for a LAN connection to a network hub. Power Up Power Up The possible LED status and conditions indicated are shown in Table 1. 8900NET Instruction Manual 17 Monitor Module Indicator LEDs Enabling Alarms and Fan Speed Control Option Establishing Frame Network Identity NetCong Application Good Networking Practices Setting Frame Network Identity Page Network Conguration Storage Web Browser Setup Web Browser Notes Addressing the Frame URL Default MAC (machine) Address Using the 8900NET GUI 8900 Frame Interface Frame Status Page 8900NET Instruction Manual 25 Using the 8900NET GUI Module Slot Status Module Slot Status icons report one of the following (Table 4): Frame Properties Older and Legacy Module Support Legacy Module Support Frame Conguration Page 8900NET Module Interface Viewing Network Module Status Network Module Conguration for SNMP SNMP Agent Installation Page Page SNMP Report Activation Media Module Slot Conguration Locate Module Slot Identication Hardware Switch Controls Slot SNMP Trap Reports Module ID and Network Parameters Rebooting the NET Module Updating Software Overview Software Update Procedure Page Page Page Page Page Page Page Page Page Page 8900NET Instruction Manual 49 Using the 8900NET GUI Figure 32. Serial Port Console and PC Network Connections Page Page Update Processing Details 8900NET Instruction Manual 53 Specications Specications Service Troubleshooting GUI Operation Cannot Open Any of the Frames Web Pages Page Page Cannot modify parameters on Web Page Cannot Connect to the Frame From a VTECS1 VideoFrame Control Panel Page Page Page 62 8900NET Instruction Manual Functional Description Functional Description Refer to the block diagram in Figure 37 while reading the following func- tional description. Temperature Sensing Page Page 8900NET Instruction Manual 65 Appendix Compatibility Matrix 66 8900NET Instruction Manual Appendix Control and Monitoring Support Control and Monitoring Notes 8900FLOADCBL Assembly Page Index Numerics A B C J L M N O V W