Technicolor - Thomson TX807C manual Daily use

tx807en2 15/01/03 12:26 Page 6

Daily use

How to switch on the set?

With the On/Off-button fitted on the set. When the red LED is lit, the TV set has previously been switched on standby with the key Bon the remote control.

If the red LED flashes, it means that the control keyboard of the TV is locked and can only be made operational again through the remote control.

In both cases, enter a channel number.

How to select a channel?

Through the digital keys of the remote control.

For the 2-digit channels (10, 11, 12, etc.) press on key 0 of the remote control.

Ò--Ó appears on the screen. Through the digital keys, enter the tens unit digit, then the unit one.

With the pr+ or pr- button of the remote control or the keypad.

If you change the channel with the pr+ or pr- buttons of the keypad, maintain the button pressed until the next or preceding channel appears on the screen.

How to select the Sound channel?

This function may only be accessed if you selected Auto on the line of the Sound menu (see p. 6). Press the blue key to successively select S1, S2 or S3 during NICAM, Stereo or Dual telecasts, or when using a device connected to one of the AV connections.

Sound received	S1	S2	S3
NICAM Stereo	Stereo	Mono	X
NICAM Dual	NICAM 1	NICAM 2	Mono
NICAM Mono	NICAM	Mono	X
Stereo	Stereo	X	X
Dual	Dual 1	Dual 2
Mono	Mono	X	X
FM Mono	X	X	X
AVsound	Stereo	Channel L	Channel R

X: Not available

How to adjust the volume?

-With the remote control, by making short pulses or maintaining the / buttons pressed.

-With the keypad of the television, by maintaining

buttons / pressed.

How to mute the sound?

With the ( ) key.

Press once more on the key to reactivate the sound.

How to display the channel number?

With the info key, display or remove the channel number and, if you want it, the time left before timer- programmed switch-off.

How to recall the preferred settings?

Press on the red key to recall the sound and picture settings you previously stored (see page 6).

How to programme a switch-off?

Press on the Green key, then using the Left/Right keys, adjust on the screen the wished-for duration before the switching-off of the TV set (by intervals of 10 minutes up to 4 hours).

To exit the menu, press exit.

When the programmed remaining time is over, the TV set will switch on standby

60 seconds before automatic cut-off, a message appears on the screen.

To cancel, first press the Green key and then, by means of the directional key Left, reset the time remaining on -:--.

The programmed switching-off is also deactivated when the TV set is turned off through its own On/Off switch.

How to prevent kids using the TV set?

Hold key Bon the remote control down for over 4 seconds until the red LED on the TV set flashes.

The keys of the TV set are now locked and switching it on again will be possible by means of the remote control only.

Keep the remote control out of the reach of children.

To unlock the keys of the TV set, make use of the number keys on the remote control.

The keys of the TV set will also remain locked after timer-programmed switching-off.

The lock function will also be activated when the TV set is switched on standby or switched off with its On/Off switch before the time remaining until programmed switching-off is over.

How to switch off the set?

To switch the TV set off, press the key Bon the remote control or use the On/Off switch on the TV set. The TV set automatically switches to stand-by after a few minutes without telecast on the selected channel.

Important:

The blue screen displaying SIGNAL = 0 either means that the television set is not receiving any signal, or that the channel on which you are tuned is receiving two signals at the same time, which is preventing the synchronisation of the television set. Change programs and if the display persists, check your antenna connection.

6