SETTING UP
Blender :
With the “click” button (D2) of the blade unit (D1) in front of you, place the base of the bowl | EN |
(D4) under the rib (D3) (fig. 2a) and then bring back the blade unit (D1) onto the bowl (fig. |
|
2b), lock by pressing the “click” button (D2) and then release it. Make sure that the bowl (D4) |
|
and the blade unit (D1) are well connected (fig. 2c). |
|
Add the ingredients in the bowl without exceeding the maximum level indicated. |
|
0.6 l for the thick preparations |
|
0.5 l for the liquid preparations |
|
Do not put liquid or any ingredients in the blender bowl where the temperature exceeds |
|
60° C (140°F). |
|
Put the lid (D6) on the bowl (D4), lock the cap (D7) in its housing situated on the lid. |
|
Fit the assembled bowl (D) on the motor unit (A), with click button (D2) of the blade unit |
|
aligned with the notch situated on the front of the motor unit (A) ( fig. 3). The bowl (D) must |
|
be pushed down far enough on the motor unit (A) or the appliance will not work (fig. 4). |
|
Accessories: |
|
With the “click” button (E2) or (F2) of the blade unit (E1) or (F1) in front of you, place the |
|
base of the bowl (E4) or (F4) under the rib (E3) or (F3) (fig. 5a) and then bring back the |
|
blade unit (E1) or (F1) to the bowl (fig. 5b), lock by pressing the “click” button (E2) or (F2) |
|
and then release it. . Make sure that the bowl (E4) or (F4) and the blade unit (E1) or (F1) are |
|
well connected (fig 5c). |
|
Check whether there is no error in the assembly of the accessories (E) and (F): the colour of the click |
|
button (E2 or F2) must correspond to the colour of the line on the base of the bowl (E4 or F4). |
|
Place the assembled accessory (E) or (F) on the motor unit (A). The click button (E2) or (F2) |
|
must be in front of you. Push it until the marking is no longer visible, otherwise the appliance |
|
will not work (fig. 6). |
|
USING YOUR APPLIANCE |
|
Blender: |
|
Plug in the appliance and press on the button 1 (C) or 2 (B), depending on the required speed, |
|
pressing several times for pulse operation or holding down for continuous operation. Do not run |
|
for more than 60 seconds. |
|
To stop the appliance, release the pressure on the button (B) or (C) unplug the appliance. |
|
Remove the bowl (D) from the motor unit (A). |
|
Accessories: |
|
Plug in the appliance. Put the ingredients into the bowl (E4) or (F4). |
|
Keep your hand supporting the bowl (E4) or (F4) and during operation press on button (B) or |
|
(C) several times in short pulses (fig 7). |
|
To stop the appliance, release button (B) or (C). Unplug the appliance. |
|
Remove the accessory (E) or (F) from the motor unit (A), turn over the accessory on the work |
|
surface and release the blade unit (E1) or (F1) by pressing on the “click” button (E2) or (F2). |
|
You can then take out your preparation. |
|
The lid (G) can be fitted on the bowl (E4) or (F4) to avoid preparations from drying out and also |
|
allows them to be kept in the refrigerator for later use. |
|
6
