Cleaning the soleplate

•While the soleplate is still slightly warm, clean it by wiping over it with a damp non-metallic cloth.

Never use abrasive or aggressive products on the soleplate.

Storing your iron

•Unplug the iron and wait for the soleplate to cool down.

•Close the Ultracord System and lock it by positionning the ring indicator (depending on model) onto .

•Empty the water tank and set the steam control to “0”. A little water may remain in the tank.

•Wind the cord around the heel at the back of the iron. Store the iron on its heel – fig.16.

If there is a problem

 

 

 

 

 

GB

PROBLEM

 

POSSIBLE CAUSES
SOLUTIONS

 

 

 

 

 

 

 

 

Water drips from the

The chosen temperature is too

Position the thermostat in the steam range

 

holes in the soleplate.

low and does not allow for the

(from •• to MAX).

 

 

 

formation of steam.

 

 

 

 

 

 

 

 

 

 

You are using steam while the iron is

Wait until the thermostat light goes out.

 

 

 

not hot enough.

 

 

 

 

 

 

 

 

 

 

You are using the Turbo button

Wait a few seconds between each use of the

 

 

 

 

too often.

Turbo button.

 

 

 

 

 

 

 

 

 

There is too much steam.

Reduce the steam.

 

 

 

 

 

 

 

 

You have stored the iron horizontally,

See the section "Storing your iron".

 

 

 

without emptying it and without

 

 

 

 

setting it to “0”.

 

 

 

 

 

 

 

 

Brown streaks come

You are using chemical descaling

Do not add any descaling agents to the water

 

through the holes in

agents.

in the water tank.

 

the soleplate and

 

 

 

 

 

 

You are not using the right type of

Perform a self-cleaning operation and

 

stain the linen.

 

water.

consult the section "What water to use?"

 

 

 

 

 

 

 

 

 

 

 

Fabric fibres have accumulated in the

Perform the self-cleaning operation and clean

 

 

 

holes of the soleplate and are burning.

the soleplate with a damp sponge. Vacuum

 

 

 

 

 

the holes of the soleplate from time to time.

 

 

 

 

 

The soleplate is dirty

You are ironing with an inappropriate

Clean the soleplate as indicated above.

 

or brown and can

setting (temperature too high).

Select the appropriate setting.

 

stain the linen.

 

 

 

 

 

 

Your linen has not been rinsed

Clean the soleplate as indicated above.

 

 

 

 

 

 

sufficiently or you are using starch.

Always spray starch onto the reverse side of

 

 

 

 

 

the fabric to be ironed.

 

 

 

 

 

There is little or no

The water tank is empty.

Fill the water tank.

 

steam.

 

 

 

 

 

 

The anti-scale valve is dirty.

Clean the anti-scale valve.

 

 

 

 

 

 

 

 

 

 

 

Your iron has a build-up of scale.

Clean the anti-scale valve and carry out a self-

 

 

 

 

 

clean.

 

Your iron has been used dry for too long. Carry out a self-clean.

The soleplate is

You have placed your iron flat on a

Always set your iron on its heel.

scratched or

metallic rest-plate or ironed over a zip.

 

damaged.

 

 

 

 

 

Water is running out

You have not closed the water tank

Check that the water tank flap is locked

of the water tank

flap properly.

properly (until your hear a "click").

flap.

 

 

 

 

 

Steam or water

The steam control is not set to the “0”

Check that the steam control is set to

leak from the iron

position.

the “0” position.

as you finish filling

 

 

the tank.

 

 

 

 

 

The spray does not

There is not enough water in the water

Fill up the water tank.

spray.

tank.

 

If you have any problem or queries, please contact our Helpline:
0845 602 1454 - UK / (01) 461 0390 - Ireland
or consult our website - www.tefal.co.uk

7