Teka DS ISLA Vr.03 manual Accesories supplied, Active charcoal filters Optional

Installation

Fig. 1 (Page 31)

On installing the kitchen hood make sure that the Safety Instructions set out on page 10 are complied with.

	Accesories supplied	The active charcoal filters have an active life of
		between three to six months, depending on
1	150/ 120 mm reduction.	the individual conditions of use. These filters
4	Screws (Ø4 x 12).	cannot be washed nor regenerated. They must
4	Screws (Ø4 x 10).	be replaced once their useful life comes to an
		end.
6	Lock screws (M8 x 45).

Fig. 1 (Page 31)

1) Mount the diffuser support (A13) onto the upper chassis (A6) with the screws (A4) (M4 x 12).

2) Adjust the diffuser (A5) over the support

(A13).

To obtain optimum performance, the external 3) Connect the upper part of the inner tube (not conduct must not be more than FOUR supplied) to the circular support exit (A13).

METRES long, have no more than two 90° 4) Using the support (O) trace and drill the angles and its diameter must be at least Ø120. where the screw-fittings will sit onto the roof (S)

(Ø8 x 45).

1)Using the support (O) trace and drill the 5) Screw the support (O) into the roof with the where the screw-fittings will sit onto the roof (S) screw-fittings (S) (Ø8 x 45).

(Ø8 x 45).			6) Mount the upper chassis	(A6) onto the
2) Screw the support (O) into the roof with the
			support (O) using the screws (Q) (M6 x 16).
screw-fittings (S) (Ø8 x 45).			7) Mount the upper cover (A8) and attach it to
3) Mount the upper chassis		(A6) onto the
			the upper chassis (A6) with the screws (G) (M4
support (O) using the screws (Q) (M6 x 16).			x 12).
4) Connect the upper part of the inner tube (not			8) Fit the part (B) if the inner tube (not supplied)
supplied) to the exit.			is Ø120.
5) Mount the upper cover (A8) and attach it to
			9) Mount the whole lower unit to the upper
the upper chassis (A6) with the screws (G) (M4			section, attaching it to the	roof using the
x 12).			screws (A10) (M4 x 12) at the required height.
6) Fit the part (B) if the inner tube (not supplied)
			10) Attach the inner tube with a clamp (not
is Ø120.			supplied) to (B) or on to the motor's air outlet
7) Mount the whole lower unit to the upper
			vent as the case may be.
section, attaching it to the roof using the			11) Mount the lower part (A9a) of the cover to
screws (A10) (M4 x 12) at the required height.			the lower chassis (A7) with the screws (I)
8) Attach the inner tube with a clamp (not			(M4x12).
supplied) to (B) or on to the motor's air outlet			12) Adjust the lower part (A9b) of the cover
vent as the case may be..			(A9a) as shown in the diagrams.
9) Mount the lower part (A9a) of the cover to
			13) Remove the metal filters. Loosen the
the lower chassis (A7) with the screws (I) (M4			screws (without unscrewing	them) of the
x 12).			EASYCLEAN panels (A19), move the panels
10) Adjust the lower part (A9b) of the cover
			aside carefully and take them off.
(A9a) as shown in the diagrams.			14) Put the filters into the lateral draught
			section of the motor making the holes in the
	Active charcoal filters	(Optional)	filters match up (A11) with the pivots (A12) of
When exterior gas extraction is not possible,			the motor carcass.
then the kitchen hood may be set to purify the			15) Mount the EASYCLEAN panel again (A19).
air by recycling it through		active charcoal	Fit the metal filters.

filters.

ENG

13