Toro specifications Groundsmaster 3280-D & 3320 Accessories Specifications

Groundsmaster® 3280-D & 3320 Accessories

Specifications* (continued)

TYPE

MOWING RATE[1]

TRIMABILITY

HEIGHT OF CUT

CONSTRUCTION

SPINDLE ASSEMBLY

CUTTER DRIVE

BLADES

CARRIER FRAME SUSPENSION

CASTER WHEELS

ANTI-SCALP

FEATURES

DECK COVERS

LIFT ARMS

OPTIONAL

EQUIPMENT

CERTIFICATION

FULL	FLOTATION CUTTING UNITS
60" SIDE DISCHARGE	GUARDIAN® 62" RECYCLER®	52" SIDE DISCHARGE
MODEL 30366	MODEL 30376	MODEL 30555
	62" REAR DISCHARGE
	MODEL 30367
60" (152 cm) width of cut, 3-blade, front	62" (157 cm) width of cut, 3-blade, front	52" (132 cm) width of cut, 3-blade, front
mounted rotary. Adjustable front baffle. Side	mounted rotary. Recycling with vertical discharge	mounted rotary. Side discharge.
discharge.	or rear discharge.
Mows up to 3.0 acres/h (1.22 hectares/h) at	Mows up to 3.1 acres/h (1.25 hectares/h) at	Mows up to 2.6 acres/h (1.1 hectares/h)
5 mph (8 km/h).	5 mph (8 km/h).	at 5 mph (8 km/h).
Offset 4.33" (10.9 cm) to the left; 42.6" (108.2 cm)	Offset 2.75" (6.9 cm) to the left; 44.5" (113 cm)	Deck offset from outside of wheel to left trim
uncut circle left. Deck overhang: 11.17" (28.4 cm)	uncut circle left. Deck overhang: 10.43" (26.5 cm)	side: 10.25" (26 cm). Uncut circle left: 26" (66 cm).
from outside of wheel to left trim side.	from outside of wheel to left trim side.	Uncut circle with use of individual wheel brakes: 0".
1" to 5" (2.5 cm to 12.7 cm) adjustable	1.5" to 5" (3.8 cm to 12.7 cm) adjustable	Adjustable in .5" (12.7 mm) increments by
.5" (12.7 mm) increments with spacers on the	in .5" (12.7 mm) increments with spacers on the	repositioning 4 clevis pins holding the deck
front and rear castor shafts. Adjustable HOC	front castor shafts. Adjustable HOC links for	suspended from carrier frame hanger brackets.
links for rear of deck.	rear of deck.	Height of cut range: 1" to 4" (2.5 to 10.2 cm)
7-gauge steel 5.5" (13.97 cm) deep; welded	7-gauge steel 4.25" (10.8 cm) deep, welded	12-gauge formed steel construction with integral
construction. 5/16" (8 mm) rubber discharge	construction.	structural ribs, 7-gauge welded support brackets
chute.		5" (12.7 cm) deep Wind-Tunnel®housing.
		Steel discharge chute.

Ductile cast iron spindle housing. Dual Timpken® greaseable tapered roller bearings. 1.25" (3.2 cm) [1" (2.5 cm) on Model 30553] diameter solid cold finished steel spindle shaft. Splined connection between spindle shaft and pulley. Welded blade retainer plus anti-scalp cups.

Isolation mounted, PTO driven gearbox with 1.25:1 spiral bevel gears. “B” section belt drive to		PTO shaft driven, isolation mounted gearbox with
all spindles. 1.25" (3.18 cm) diameter spindle mounted in two greaseable tapered roller bearings.		1.25:1 spiral bevel gears. Gearbox pulley drives
		a single “AA” section belt to 3 spindles,
		self-tensioned with a rubber torsion idler arm and
		riveted steel idler pulley with ag-type wiper
		seal and bearing.
Three 20.5" (52 cm) long, .25" (6 mm) thick,	Three 21.75" (55 cm) long, .25" (6 mm) thick,	Three 18" (46 cm) long, 2.5" (6.3 cm) wide,
2.5" (6.35 cm) wide, heat-treated steel blades.	2.5" (6.35 cm) wide, heat-treated steel blades.	.19" (5 mm) thick, heat-treated steel blades.
Optional Atomic™ Mulching Blade.	Optional Atomic Mulching Blade.	Optional Atomic Mulching Blade, P/N 104-1301.
Independent, 2.5" (6.35 cm) square tubing, lift/push arms each attached to separate castor arms.		Mower freely suspended in patented carrier frame.
		Height of cut bracket design and flexible carrier
		frame enhance cutting unit flotation and ground
		following capability.
Front: Two 8.0" x 3.5" (20.3 cm x 8.9 cm) pneumatic tires (foam filled optional) with tubes and		Pneumatic, 8" turf tread tires, 8 x 3-4
maintenance-free bearings. Tensioning caps made from GE XENOY 6230 impact modified		regreaseable roller bearings and heavy duty
thermoplastic alloy are used to hold the castor wheels on the castor arms.		bushings rotating on a replaceable spanner.
		(Optional Phenolic Caster Wheel Assembly,
		P/N 27-1050; two required.)
6 rollers. Anti-scalp cup located on each	5 rollers on Rear discharge Deck, 6 rollers on	Anti-scalp roller.
blade spindle.	Guardian Deck. Anti-scalp cup located on each
	blade spindle.
Quick-release type latches; no tools required.
Independent lift arms and hydraulic weight transfer provide deck flotation.		High strength lift arms with mounting provision for
		quick attach-detach of mower carrier frame or
		other attachments.
Rear Weight Kit, Collection System, High Tip	Rear Discharge Conversion Kit, Guardian	Rear Weight Kit, Collection System.
Speed Kit, Striping Kit, Leaf Mulcher Kit.	Recycler Conversion Kit, Rear Weight Kit.
Cutting unit meets specification of American	Cutting unit meets specification of American	Certified to meet the American National Standard
National Standard ANSI B71.4-2004, Safety	National Standard ANSI B71.4-2004, Safety	Institute’s (ANSI) specifications, B71.4-1999 and
Specifications for commercial turf care equipment.	Specifications for commercial turf care.	applicable Federal and State regulations based
Cutting unit meets specifications of European	Cutting unit meets specifications of European	equipment thereon.
standard EN836, CE approved, except some	standard EN836, CE approved.
blades and the High Tip Speed Kit.

*Specifications and design subject to change without notice. Products depicted in this literature are for demonstration purposes only. Actual products offered for sale may vary in design, required attachments and safety features. Consult your local Toro Distributor.

[1] Mowing rate is dependent on conditions.