Key Label

Toshiba TV

Cable

Satellite

VCR

DVD/LD

Receiver

CD/MD

Cassete

(TV)

(CBL/SAT)

(CBL/SAT)

 

 

(AUDIO)

(AUDIO)

(VCR)

 

 

 

TV/VCR

VCR

---

TV/SAT

TV/VCR

---

---

---

Reverse

AM/FM

---

---

---

---

Disc shift

AM/FM

Disc shift

Deck side

DISC

 

 

 

 

 

 

 

A/B switch

STOP

VCR

VCR

VCR

Stop

Stop

---

Stop

Stop

REC**

VCR

VCR

VCR

Record**

---

---

---

Record**

POP CH yz

POP channel

TV

TV

TV

TV

TV

TV

TV

 

up/down

 

 

 

 

 

 

 

SPLIT

POP Split

TV

TV

TV

TV

TV

TV

TV

POP DIRECT CH

POP Direct ch

TV

TV

TV

TV

TV

TV

TV

FREEZE

POP Freeze

TV

TV

TV

TV

TV

TV

TV

SWAP

POP Swap

TV

TV

TV

TV

TV

TV

TV

CH SCAN

POP Ch scan

TV

TV

TV

TV

TV

TV

TV

SOURCE

POP Source

TV

TV

TV

TV

TV

TV

TV

Note:

 

 

 

 

 

 

 

 

“---” will send nothing.

• “ TV” will jump to TV.

• “VCR ” will jump to last active VCR or DVD. Active VCR/DVD is defined as the mode that remains for a minimum of 5 seconds, or if a key is pressed in that mode.

*The VOLUME and MUTE will jump to “TV” by default. When the volume is unlocked, all the devices will have their own volume. The AUDIO1/2 (Receiver, CD) modes will have their own volume even if Volume Lock is on TV, CABLE/SAT, VCR, or DVD. See “Using the Volume Lock feature” on page 18.

**Press the REC button two times within 5 seconds to record each audio/video source.

Introduction

 

 

 

 

 

Connecting

yourTV

 

 

 

 

Usingthe

RemoteControl

 

 

up

TV

TV

POWER

Programming the remote control for use with your audio/video devices

Device code setup

CABLE/SAT

LIGHT

SLEEP

POWER

VCR

 

 

 

DVD

1

2

3

AUDIO1

 

 

Numbers

AUDIO2

4

5

6

 

MODE

MODE

7 8 9

1.Refer to the Device code table on pages 19 – 20 to find the code for the brand of your device.

If more than one number is listed, try each one separately until you find the one that works.

2.Press MODE until the Mode indicator of the device (CABLE/ SAT, VCR, DVD, AUDIO1, AUDIO2) lights up.

3.While holding down the RECALL button, press the Channel Number buttons to enter the four-digit code of your brand of device. If a valid code is entered, the mode indicator will blink twice. If an invalid code is entered, the mode indicator will blink one long blink.

4.Point the remote control at the device and press POWER to test the code.

If the device turns on, you have entered the correct code.

If the device does not respond to the remote control, you may have entered the wrong code. Repeat steps 3 and 4 using another code.

Note: In addition to POWER, confirm that all necessary keys on the TV remote control operate your device. If some keys are not operational, repeat the device code setup using another code (if other codes are listed for your device). If,ºafter trying all listed codes, the necessary keys do not operate your device, use the device’s original remote control.

5. Press MODE to select the TV mode to control the TV.

PIC SIZE

 

+10

 

 

 

 

 

 

ACTION

 

100/

 

 

0

ENT

 

 

MENU

 

O

FAV

ORI

 

 

 

 

 

NF

 

 

T

 

 

 

 

I

 

 

 

TE

 

 

 

 

 

 

 

 

 

HE

 

 

E

 

 

 

 

 

LI

AT

 

 

 

 

 

 

 

E

ID

 

 

 

 

 

N

 

R

U

 

 

 

 

 

 

K

 

 

G

 

LE

SUB

TIT

 

 

 

 

 

 

 

 

 

 

 

 

TIT

 

 

 

 

 

 

 

 

 

 

LE

A

 

 

 

P

 

 

 

 

 

 

 

 

U

 

 

 

 

 

U

 

 

 

T

 

FAV

 

 

DI

 

 

 

SE

 

 

 

O

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ENTER

 

 

 

 

 

 

 

 

FAV

 

 

 

 

 

 

CH

 

 

 

 

 

VOL

 

 

 

DVD RTN

 

EXIT

 

 

 

 

 

RECALL

 

DVD CLEAR

 

 

 

 

CH RTN

 

INPUT

RECALL

MUTE

 

 

SLOW/DIR SKIP/SEARCH

Note:

Every time you replace the batteries, you must reprogram the remote control.

Some newer VCRs are capable of working on either of two remote codes.These VCRs have a switch labeled “VCR1/VCR2.” If your VCR has this kind of switch and does not respond to any of the codes for your VCR brand, set the switch to the other position (VCR1 or VCR2) and reprogram the remote control

Although the remote control for your new TV includes codes for many devices, it may not include codes for some or all of the features on certain devices you want to

control. If you are unable to program the

Setting

your

 

 

UsingtheTV’s

Features

 

 

 

 

Appendix

 

 

 

 

 

Index

 

 

 

17