Toshiba camera control unit manual

CAMERA CONTROL UNIT

IK-HD2C

INSTRUCTION MANUAL

For Customer Use

Enter below the Serial No. which is located on the bottom of the cabinet. Retain this information for future ref- erence.

Model No.: IK-HD2C Serial No.:

FCC NOTICE

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

USER-INSTALLER CAUTION: Your authority to operate this FCC veriﬁed equipment could be voided if you make changes or modiﬁcations not expressly approved by the party responsible for compliance to Part 15 of the FCC Rules.

Canada ICES-003 Compliance Lable:

CAN ICES-3 A/NMB-3A

Following information is only for EU-member states:

In residential areas this product may cause radio interference, therefore this product must not be used in residential areas.

Following information is only for EU-member states:

The use of the symbol indicates that this product may not be treated as household waste. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about the take- back and recycling of this product, please contact your supplier where you purchased the product or consult.

This manual is made from recycled paper.

Contents

For Customer Use SAFETY PRECAUTIONS Safety icons Stop operation immediately if any abnormality or defect occurs Avoid installing in a shower room or a bathroom Do not operate in places where the product may get wet Disclaimer Copyright and Right of Portrait Protection of Personal Information TABLE OF CONTENTS Page 1. CAUTIONS ON USE AND INSTALLATION 2. COMPONENTS 3ITEMS CONTROLLED BY THE ON SCREEN DISPLAY 4. NAMES AND FUNCTIONS CONNECTION 52 Caution on Connection 53 Connection on Back Panel Back panel view 4 A Connector Pin Assignments 6OPERATION 61 Automatic Black Balance 62 White Balance AWB OK AWB NG LEVEL LOW LEVEL HIGH C. TEMP LOW 63 Scene File 64 Gain 65 Shading Correction 7MODE SETTING BY THE ON SCREEN DISPLAY 71 Using the Menus 72 Menus 1SHUTTER䟺Electronic shutter䟻䟺1䠀1䟻 Changing the setting in AUTO mode (a)Changing the video level in the automatic shutter mode (b) Changing the automatic shutter detection (ratio between peak and average value) (c) Changing the automatic shutter response speed (d) Changing the automatic shutter zone area 䟺1䠀2䟻 Changing the setting in MANUAL mode (a)Changing the shutter speed 䟺1䠀3䟻 Changing the setting in SS (Synchro. Scan) mode (a)Changing the shutter speed setting 2GAIN (Video gain) 䟺3䟻 WHT BAL(White Balance) (e) Confirming the contents of the zone area selected by AWB 䟺3䠀2䟻 Changing the setting in ATW(Automatic Tracking White balance) mode (a) Changing R PAINT (b) Changing B PAINT 䟺3䠀3䟻 Changing gain in MANUAL mode (1) Changing the red gain (2) Changing the blue gain 䟺4䟻 PROCESS 䟺4䠀3䟻 Changing black gamma correction level 䟺4䠀4䟻 Changing detail (outline) gain 䠄4䠊5䠅 Changing pedestal (a) Changing master pedestal (b)Changing R. PED (red pedestal) 䟺5䟻 MATRIX(Matrix color correction) 䟺6䟻 SYNC 䟺7䟻 OPTION 䟺7䠀4䟻 Changing RGB SYNC * When Y/Pb/Pr is selected at OUTPUT, RGB SYNC change cannot be adjusted 䟺7䠀5䟻 Changing detail signal output 䟺7䠀6䟻 Changing RS232C baud rate 䟺7䠀7䟻 Changing OSD OUTPUT mode 䠄8䠅 Setting USER area 䟺9䟻 Returning to factory settings 73 External Sync 䟺1䟻 External sync signal input conditions 2External sync frequency range 3Using the unit with external sync signal 8. BEFORE MAKING SERVICE CALL 9.SPECIFICATIONS 10. EXTERNAL APPEARANCE DIAGRAM Page Limited Warranty – TOSHIBA Camera Control Unit One (1) Year Limited Warranty of Labor and Parts Instruction Manual (Owner’s Manual): Your Responsibilities DISCLAIMERS: