Toshiba camera control unit 10. EXTERNAL APPEARANCE DIAGRAM

10. EXTERNAL APPEARANCE DIAGRAM

[Front]

60I

[Rear]

Unit : mm [inch]

㻔㻔㻓㻃㻾㻗㻑㻖㻖㼀

		㻔㻛㻑㻛㻖
	㻔㻛㻙㻃㻾㻚㻑㻖㻕㼀	㻾㻓㻑㻚㻗㼀

㻗㻗㻑㻙㻃㻾㻔㻑㻚㻙㼀

㻗㻓㻃㻾㻔㻑㻘㻛㼀

㻗㻐㻰㻖㻃㻥㻧

㻙㻕㻓㻑㻔㻃㻾㻕㻑㻗㻗㻓㻑㻓㻓㻗㼀

㻕㻚㻃㻾㻔㻑㻓㻙㼀

㻔㻖㻜

㻓㻑㻔㻘㻃㻾㻘㻑㻗㻚㻕

㻓㻑㻓㻓㻙㼀

Contents

For Customer Use SAFETY PRECAUTIONS Safety icons Stop operation immediately if any abnormality or defect occurs Avoid installing in a shower room or a bathroom Do not operate in places where the product may get wet Disclaimer Copyright and Right of Portrait Protection of Personal Information TABLE OF CONTENTS Page 1. CAUTIONS ON USE AND INSTALLATION 2. COMPONENTS 3ITEMS CONTROLLED BY THE ON SCREEN DISPLAY 4. NAMES AND FUNCTIONS CONNECTION 52 Caution on Connection 53 Connection on Back Panel Back panel view 4 A Connector Pin Assignments 6OPERATION 61 Automatic Black Balance 62 White Balance AWB OK AWB NG LEVEL LOW LEVEL HIGH C. TEMP LOW 63 Scene File 64 Gain 65 Shading Correction 7MODE SETTING BY THE ON SCREEN DISPLAY 71 Using the Menus 72 Menus 1SHUTTER䟺Electronic shutter䟻䟺1䠀1䟻 Changing the setting in AUTO mode (a)Changing the video level in the automatic shutter mode (b) Changing the automatic shutter detection (ratio between peak and average value) (c) Changing the automatic shutter response speed (d) Changing the automatic shutter zone area 䟺1䠀2䟻 Changing the setting in MANUAL mode (a)Changing the shutter speed 䟺1䠀3䟻 Changing the setting in SS (Synchro. Scan) mode (a)Changing the shutter speed setting 2GAIN (Video gain) 䟺3䟻 WHT BAL(White Balance) (e) Confirming the contents of the zone area selected by AWB 䟺3䠀2䟻 Changing the setting in ATW(Automatic Tracking White balance) mode (a) Changing R PAINT (b) Changing B PAINT 䟺3䠀3䟻 Changing gain in MANUAL mode (1) Changing the red gain (2) Changing the blue gain 䟺4䟻 PROCESS 䟺4䠀3䟻 Changing black gamma correction level 䟺4䠀4䟻 Changing detail (outline) gain 䠄4䠊5䠅 Changing pedestal (a) Changing master pedestal (b)Changing R. PED (red pedestal) 䟺5䟻 MATRIX(Matrix color correction) 䟺6䟻 SYNC 䟺7䟻 OPTION 䟺7䠀4䟻 Changing RGB SYNC * When Y/Pb/Pr is selected at OUTPUT, RGB SYNC change cannot be adjusted 䟺7䠀5䟻 Changing detail signal output 䟺7䠀6䟻 Changing RS232C baud rate 䟺7䠀7䟻 Changing OSD OUTPUT mode 䠄8䠅 Setting USER area 䟺9䟻 Returning to factory settings 73 External Sync 䟺1䟻 External sync signal input conditions 2External sync frequency range 3Using the unit with external sync signal 8. BEFORE MAKING SERVICE CALL 9.SPECIFICATIONS 10. EXTERNAL APPEARANCE DIAGRAM Page Limited Warranty – TOSHIBA Camera Control Unit One (1) Year Limited Warranty of Labor and Parts Instruction Manual (Owner’s Manual): Your Responsibilities DISCLAIMERS: