Preparation (continued)

E: Ethernet

Perform this setting if you connect the player to your LAN ( page 17).

After performing this setting, you need to turn off this player and turn it on again to activate this setting. If you do not connect, skip to Step 20.

18

Press

/

to select “Ethernet”, then press OK.

19

Press

/

to select each of the followings, then press OK.

DHCP

Off

 

 

Proxy Setting

Off

 

 

Mac Address

Off

 

 

NTP Server

Off

 

 

Network Speed

56kbps Modem

 

 

Cookie Setting

Accept

1To set your network information.

2To input proxy server address (when your provider requires the setting). To display the Mac address of the player. (Fixed. No need to set.)

3To adjust the player’s clock via the network time protocol.

4To select the speed according to the specification of your LAN.

5To select whether you access “Cookies” or not.

1 DHCP

2 Proxy Setting

Enter the proxy server address when your provider

1Set “DHCP” to “On” and press OK button.

The network information is automatically set.

2Set “DNS” to “On” and press OK button.

The DNS server is obtained automatically from the DHCP server.

3Select “Confirm”, then press OK button. Confirming starts.

If the setup is successful, an IP address appears. Press OK button.

 

DHCP

 

 

DHCP

 

On

 

Off

 

IP Address

0

.

0 .

0 .

0

Subnet Mask

0

.

0 .

0 .

0

Gateway

0

.

0 .

0 .

0

Skipped when “DHCP”

is set to “On”.

 

Gateway

0

.

0 .

0 .

0

DNS

 

On

 

Off

 

DNS Server

0

.

0 .

0 .

0

Confirm

 

 

 

OK

 

Cancel

 

 

Skipped when “DNS”

is set to “On”.

 

requires proxy setting.

1 Set “Proxy” to “On” and

 

Proxy Setting

 

 

 

 

 

 

press OK button.

Proxy

On

Off

 

 

 

 

 

 

 

 

Server

 

 

 

 

 

 

 

 

 

 

 

 

 

2 Enter the specified data

Port

0

 

 

 

 

 

 

 

 

 

 

from the provider.

 

OK

Cancel

 

Refer to the instructions

 

 

 

 

 

 

below for inputting

3 Select “OK” and press

characters. (Server, Port)

OK button.

 

 

 

 

 

 

How to input characters

 

 

 

 

 

 

 

 

OK button

To begin or finish input.

 

 

 

If the setup is not successful:

a) Set “DHCP” to “Off” and

 

DHCP

 

 

 

 

 

 

 

 

 

 

 

 

 

press OK button.

DHCP

On

 

 

 

Off

 

IP Address

 

 

 

 

 

 

 

 

 

The network information is

192

.

168

 

1

.

15

 

 

 

 

 

 

 

 

 

 

automatically set.

Subnet Mask

255

.

255

 

255

.

0

 

 

 

 

 

 

 

Gateway

192

.

168

 

1

.

1

 

 

 

 

 

 

DNS

On

 

 

Off

 

 

DNS Server

 

 

 

 

 

 

 

 

 

 

192

.

168

.

1 .

1

 

 

 

 

 

 

 

 

 

Confirm

 

 

 

/

buttons

To select a character.

/

buttons

To move to the next character.

 

 

CLEAR button

To erase to correct.

 

 

Number buttons

To input a number.

b) Input the addresses using the number buttons.

OK Cancel

“IP Address”

This sets a di

fferent address within the

 

 

 

same subnet of the PC on your network.

 

e.g. if the IP address of the PC is

 

192.168.1.10, set 192.168.1.15 (or some

 

other unused address.)

 

“Subnet Mask”

This sets the subnet mask of the network

 

environment that will be connected.

 

e.g.: 255.255.255.0

 

“Gateway”

This sets the gateway used by the player

 

(e.g.: 192.168.1.1).

 

 

 

“DNS Server”

This sets the DNS server to be used by the

 

player (e.g.: 192.168.1.1).

3 NTP Server

Select “On” or “Off” and press OK button.

“On” The player automatically accesses an internet server to adjust time protocol.

“Off” The player does not access an internet server

to adjust its clock.

NTP Server

On

Off

c) Select “OK” and press OK button.

22

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

Page 22
Image 22
Toshiba HD-A3KC owner manual Press To select Ethernet, then press OK, To select each of the followings, then press OK