Toshiba RBC-AMS41E Selecting the remote controller functions, Switches of the remote controller

Selecting the remote controller functions

•Change the settings of the remote controller functions as required by taking the steps below.

How to change the remote controller functions

1While operation is shut down, push the button

(43) and button (48) together for at least 4 seconds.

• The numeric displays and display blink, and the fixed louvers display lights.

2Push the TEMP and buttons (49).

• Repeatedly push the buttons until the setting to be changed blinks on the display.

Code No.13
O: Display	X: No display
	Scheduled operation		Scheduled operation
	underway		in standby
Setting	Air	Air	Air	Air
	conditioner	conditioner	conditioner	conditioner
	now	now shut	now	now shut
	operating	down	operating	down
0000	O	O	O	O
0001	X	X	X	X
0002	O	O	X	X
0003	O	X	X	X
0004	O	O	O	X
0005	O	X	O	X

3Push the TIME and buttons (40).

•Repeatedly push the buttons until the setting to be changed blinks on the display.

4Push the button (42). Then push the button (43) to return to the original screen.

•When the button (42) is pushed, the numeric

displays and display stop blinking and light up, and when the button (43) is pushed again, they go off.

Items to be set

•24-hour/12-hour display setting <code No.10>

–The 24-hour display or 12-hour (AM/PM) display can be selected for the clock which is displayed on the remote controller.

–This item’s selection is also reflected on the clock displayed on the clock setting screen and program input screen.

Setting Description

0000: 24-hour display (factory setting)

0001: 12-hour (AM/PM) display

•Restriction on button operations <code No.12> This item sets the range of the restriction placed on the button operations which can be applied while scheduled operations are being performed. Setting: 0000 (factory setting)

Code No.12

O: Can be operated.

X: Cannot be operated.

Setting	[ON/OFF]	[MODE]	[TEMP.]
0000	O	O	O
0001	X	O	X
0002	X	X	X
0003	O	X	X
0004	O	X	O

•Display/non-display of clock <code no.13>

This item selects and sets whether the day of the week and clock time are to be displayed.

Setting: 0000 (factory setting)

•	Selection of operation when power is restored after a
	power outage <code No.14>	G
	This item selects the operation to be performed when
	power is restored after a power￿￿outage occurred
	during a scheduled operation.
	0000: No operations are performed when the power is
		￿R￿
	restored, and the scheduled operation is resumed as
		￿
	soon as the program time is reached after the power
	has been restored. (When the power is restored, the
	scheduled operation is based￿￿Uon the operation of the
	indoor units.)	￿
			EN
	0001: If there was a programmed operation during the
		￿P
	power outage, that operation is performed when the
		￿￿
	program is resumed. If there is no programmed
	operation or if the “Continue xx” setting is in place, the
		￿A
	operation prior to the power outage is resumed.
		￿￿￿
Selecting the functions using the DIP
switches of the remote controller
• The following functions can be.￿dselected using the DIP
	switches on the remote controller’s circuit board.
Setting procedure		o.o .
• Open the back cover of the remote controller, and
	select the functions using the DIP switches located at
	the bottom left of the circuit board.
•	After establishing the settings, turn the ground fault
	interrupter off and then back on.

Setting items

•Remote controller header/follower setting: Bit 1 When operating the air conditioner using two remote controllers, set one of the controls to be the follower.

*Set the remote controller used as the schedule timer to be the header.

•Operation function setting: Bit 2

One of the following three operation functions can be selected and set.

1.Scheduled operation function 2.Timer operation function

3.No scheduled or timer operation function

MB FRIGO Grupa d.o.o., Bani 81, 10010 Zagreb, www.toshiba.hr, e-mail: toshiba@mbfrigo.hr

19