20 EN

Initial Setting

When you turn on this unit for the first time, you need to follow
these steps.
1Press [BON\STANDBY].
2Turn the TV on. Select the input to which the
unit is connected.
3Select your desired tuning type according to
your area using [K\L], then press
[ENTER\OK].
The unit will start getting channels available in your area.
Digital tuning:
Only the DVB channels receivable in your area are
automatically scanned and memorised.
Digital & Analog tuning:
Both analogue and DVB channels receivable in your area
are scanned and memorised automatically.
Analog tuning:
Only the analogue channels receivable in your area are
automatically scanned and memorised.
• If no channel has been memorised, the antenna
confirmation display will appear. Press [ENTER\OK] to start
auto scanning again or press [RETURN\BACK] to cancel
the initial settings.
4After finishing channel setting, “Clock Setting”
will appear.
• The current date and time will appear automatically.
•
If the current date and time are correct, press
[RETURN\BACK]
to exit, if they are incorrect, press
[ENTER\OK]
and follow to “
Clock Setting” on
page 71
.
Note
• After “Initial Setting”, if you need to unplug the mains cable,
make sure to turn off the power first and leave it in standby
mode for at least 1 minute before attempting to unplug.
Otherwise, it may cause data loss.
If you want to set each item of “Initial Setting” again, you can
set them at “General Setting”.
• Refer to “Auto Tuning (DVB & ANALOG)” on this page.
• Refer to “Auto Tuning (ANALOG)” on page21.
• Refer to “Auto Tuning (DVB)” on page22.
• Refer to “Clock” on page 71.
Also you can customize the memorised channel at “General
Setting”.
Refer to following pages for details.
• Refer to “Manual Tuning (ANALOG)” on page21.
• Refer to “Manual Tuning (DVB)” on page22.
• Refer to “Skip a Preset Channel” on page 22.
• Refer to “Move” on page 22.
Use this feature to adjust the aspect ratio of the video source
which is different from your TV’s ratio to fit your TV monitor
without distorting the picture.
1In stop mode, press [SETUP]. Select “General
Setting” using [K\L], then press [ENTER\OK].
2Select “Video” using [K\L], then press
[ENTER\OK].
3Select “TV Aspect” using [K\L], then press
[ENTER\OK].
4Select the desired option using [K\L], then
press [ENTER\OK].
5Press [SETUP] to exit.
Note
If you have a standard TV:
• Select “4:3 Letter Box” for a full width picture with black
bars at the top and bottom.
• Select “4:3 Pan & Scan” for a full height picture with both
sides trimmed.
If you have a wide screen TV:
• Select “16:9 Wide”.

Channel Setting

You can retune this unit or edit the channel setting with
following methods.
Programme the tuner to scan both analogue and DVB
channels you can receive in your area.
1In stop mode, press [SETUP]. Select “General
Setting” using [K\L], then press [ENTER\OK].
“General Setting” menu will appear.
2Select “Channel” using [K\L], then press
[ENTER\OK].
Basic Setup / TV View Operation
Auto Tuning
Make sure the antenna is
connected to “ANTENNA IN” jack.
Digital tuning
Digital & Analog tuning
Analog tuning

&2)
#LOCK3ETTING
Selecting the TV Aspect Ratio
Auto Tuning (DVB & ANALOG)
DVB ANALOG
TV Aspect
Video Out
46!SPECT
,ETTER"OX
0AN3CAN
7IDE
E3TK6BD_EN.book Page 20 Wednesday, February 17, 2010 10:18 AM