
Storing Channels on the VCR (continued)
Adding channels
If a desired channel cannot be scanned automatically because of a weak signal, it can be added to the memory.
Erasing channels
You can erase a stored channel from the memory if it is unnecessary.
1)Follow steps 1 to 3 of “Incoming Antenna/CATV Signals”.
2)Select “ADD CH” or “ERASE CH” usingCURSOR UP or CURSOR DOWN.
To add channels |
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
| PROGRAM |
| SET UP |
|
|
| PRESET |
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| TV |
| CATV |
| ||
|
|
|
| TV / CATV |
|
|
| ||||||
|
|
|
|
|
|
|
| OFF |
| On |
| ||
AUTO SCAn |
|
| |||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ADD CH |
|
|
|
|
| – |
| ||
|
|
|
| ERASE CH |
|
|
|
|
| – |
| ||
|
|
|
| TO SET CH |
|
|
| ||||||
|
|
|
| PUSH 0~9 KEYS |
| ||||||||
|
|
| EnD: PROG |
|
|
|
|
|
|
|
| ||
To erase channels |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
| PROGRAM |
| SET UP |
|
|
| PRESET |
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| TV / CATV |
|
| TV |
| CATV |
| |||
|
|
| AUTO SCAn |
|
| OFF |
| On |
| ||||
|
|
|
| ADD CH |
|
|
|
|
| – |
| ||
|
|
|
| ERASE CH |
|
|
|
|
| – |
| ||
|
|
|
| TO SET CH |
|
|
| ||||||
|
|
|
| PUSH 0~9 KEYS |
| ||||||||
|
|
| EnD: PROG |
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
3)Enter a channel number of 1 to 125 using number buttons.
For more than 100 number, first press 100. For CATV channels, refer to the chart below. (For other orders, check with your cable company.)
4)Repeat steps 2) and 3) to add or erase channels as necessary.
5)Press PROG to exit.
To set the Cable Box/DSS output Channel on the VCR.
1)Press PROG to display the MENU screen.
2)Select “PRESET” usingCURSOR RIGHT or CURSOR LEFT, and press ENTER.
3)Select “CABLE BOX/DSS” usingCURSOR UP or CURSOR DOWN, and press ENTER.
PROGRAM
SET UP
PRESET
USEnO C . BOX DSS
EnD: PROG
4)Select “NO”, “C.BOX” or “DSS” usingCURSOR RIGHT or CURSOR LEFT according to your connection type.
5)If set to “C.BOX” or “DSS”, select “OUTPUT CH” using CURSOR UP or CURSOR DOWN. Then enter the output channel number of your cable box (Usually 3 or 4, check the rear of the cable box.) or line input mode “L1” using theINPUT SELECT button according to your connection.
PROGRAM
SET UP
PRESET
USEnO C . BOX DSS
OUTPUT CH3 CH
TO SET CH
PUSH 0~9 KEYS
EnD: PROG
6)Press PROG to exit.
Once the active channels have been stored, you can select the channels in two ways below.
Number buttons
To enter digits of the channel number.
•For
•For more than 100 number, first press 100.
•Each number button needs to be pressed within 2 seconds.
CH
To shift up or down the stored channel numbers.
1 8