Transition Networks E-CX-MC02 specifications FCC Regulations, Trademarks

Specifications:

Case size dimensions:	3.5" x 3.75" x 1.25" (89 mm x 95 mm x 32 mm)
AUI Port:	Male DB-15 with locking posts.
AUI Connection:	Use only an IEEE 802.3 equivalent AUI
	cable.
Connector Legend:	1	Logic Ref.	9	Collision-
	2	Collision+	10	Transmit-
	3	Transmit+	11	Logic Ref.
	4	Logic Ref.	12	Receive-
	5	Receive+	13	Power
	6	Power Return	14	Logic Ref.
	7	N/C	15	N/C

8Logic Ref.

AUI Drop Cable Maximum Distance: 50 meters (165 feet)

10Base5 Cable Maximum Distance:	500 meters (1640 feet)
10Base2 Cable Maximum Distance:	185 meters (610 feet)
Environment:	0–50 degrees C,
	10–90% humidity, non-condensing,
	0–10,000 foot altitude
Warranty:	Five years

FCC Regulations:

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own cost.

NOTE:	This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out
	on the radio interference regulations of the Canadian Department of Communications.
NOTE:	This equipment has been tested and found to comply with VDE Class B requirements.

For selling in the Federal Republic of Germany:

Hiermit wird bescheinigt, das der E-FRL-MC01 oder E-FRL-MC01(SMA) in Ubereinstimmung mit den Bestimmungen der Vfg. 243/1991 funk-entstoert ist. Der Deutschen Bundespost wurde das Inverkehgringen dieses Geraetes angezeigt und die Berechtigung zur Ueberpruefung der Serie auf Einhaltung der Bestimmungen eingeraumt. TRANSITION Networks, Inc.

Canadian Regulations:

Note: This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out on the radio interference regulations of the Canadian Department of Communications.

Copyright Restrictions

© 1995 Transition Networks, Inc.

All rights reserved. No part of this work may be reproduced or used in any form or by any means - graphic, electronic, or mechanical - without written permission from Transition Networks, Inc.

Trademarks:
Ethernet is a registered trademark of the Xerox Corporation, Inc.
ST is a trademark of AT&T.
TRANSITION Networks and Micro-Ceiver are trademarks of TRANSITION Networks	7315 E

Minneapolis, MN 55344 USA

Ethernet Coaxial Transceiver

E-CX-MC02, E-CX-MC03, E-CX-MC04, E-CX-MC05

USER’S GUIDE

The TRANSITION Networks Ethernet™ Coaxial Transceiver (E-CX-MC02, E-CX-MC03, E-CX-MC04, or E-CX-MC05) is designed to provide connection between the Thick (10Base5) or Thin (10Base2) coaxial Ethernet environment and a PC or hub with an AUI connector.

Power

SQE Enabled

Ethernet™

Coaxial

Transceiver

T R A N S In Te tIw Oo rNk s

Mpls, MN 55344

The TRANSITION Networks Ethernet™ Coaxial Transceiver part numbers indicate the AMP tap that is shipped with the Coaxial Transceiver:

E-CX-MC02:	with AMP non-intrusive tap	228752-1
E-CX-MC03:	with AMP N-Series intrusive tap,	221914-1
E-CX-MC04:	with AMP BNC-T connector	221918-1
E-CX-MC05:	with AMP BNC vertical adapter	222455-1

All Ethernet™ Coaxial Transceivers provide a male AUI connector.

Status LEDs on the Ethernet Coaxial Transceiver provide the following information:

Power: Illuminated green LED indicates power through the AUI connector.

SQE Enabled Illuminated green LED indicates the SQE jumper is set to ON.