Cable Specifications -- Continued
Copper Cable
Category 5: (minimum requirement) |
|
Gauge: | 24 to 22 AWG |
Attenuation: | 22.0 dB /100m @ 100 MHz |
Maximum Cable Distance: | 100 meters |
•
•Shielded
•Pins 1&2 and 3&6 are the two active pairs in an Ethernet network .
•
•Use only dedicated wire pairs for the active pins:
(e.g., blue/white & white/blue, orange/white & white/orange, etc.)
•Do not use flat or silver satin wire.
|
| Crossover Cable |
| |||||||||
Twisted Pair #1 |
|
| 1 |
|
| 1 |
| Twisted Pair #1 | 1 |
|
| 1 |
|
| 2 |
|
| 2 |
| 2 |
|
| 2 | ||
|
|
|
|
|
|
|
|
| ||||
Twisted Pair #2 |
|
| 3 |
| 3 |
| Twisted Pair #2 | 3 |
|
| 3 | |
|
|
|
|
| ||||||||
|
| 6 |
|
| 6 |
| 6 |
|
| 6 | ||
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
Please note the following when wiring the network:
•Signal lines must not be directly connected to outdoor wiring.
•Use separate paths to route the power wiring and the signal wiring. If power wiring and signal wiring paths must cross, make sure the wires are perpendicular at the intersection point.
•Do not run signal wiring and power wiring in the same wire conduit. To avoid interference, wires with different signal characteristics should also be routed separately.
•Use the type of signal transmitted through a wire to determine which wires should be kept separate. The rule of thumb is that wiring with similar electrical characteristics can be bundled together.
•Keep input wiring and output wiring separate.
•Where necessary, label the wiring to all devices in the network.
NOTE: This device has been evaluated as EEx nC IIC T4 equipment under DEMKO Certificate No. 03 ATEX 0324537U. Each module is suitable for use in Zone 2 Explosive Atmospheres. The device must be installed in a minimum IP 54 enclosure as defined in IEC 60529 and EN 60529.
NOTE: This unit is a
Cable Specifications
The physical characteristics must meet or exceed IEEE 802.3™ specifications.
Fiber Cable
Bit Error Rate: |
| |
Single mode fiber (recommended): | 9 µm |
|
Multimode fiber (recommended): | 62.5/125 µm |
|
Multimode fiber (optional): | 100/140, 85/140, 50/125 µm | |
Standard Models |
|
|
| 1300 nm multimode | |
Fiber Optic Transmitter Power: | min: | max: |
Fiber Optic Receiver Sensitivity: | min: | max: |
Link Budget: | 16.0 dB |
|
| 1310 nm single mode | |
Fiber Optic Transmitter Power: | min: | max: |
Fiber Optic Receiver Sensitivity: | min: | max: |
Link Budget: | 19.0 dB |
|
| 1300 nm multimode | |
Fiber Optic Transmitter Power: | min: | max: |
Fiber Optic Receiver Sensitivity: | min: | max: |
Link Budget: | 16.0 dB |
|
| 1310 nm single mode | |
Fiber Optic Transmitter Power: | min: | max: |
Fiber Optic Receiver Sensitivity: | min: | max: |
Link Budget: | 19.0 dB |
|
Extended Temperature Models |
|
|
| 1300 nm multimode | |
Fiber Optic Transmitter Power: | min: | max: |
Fiber Optic Receiver Sensitivity: | min: | max: |
Link Budget: | 16.0 dB |
|
| 1310 nm single mode | |
Fiber Optic Transmitter Power: | min: | max: |
Fiber Optic Receiver Sensitivity: | min: | max: |
Link Budget: | 19.0 dB |
|
| 1300 nm multimode | |
Fiber Optic Transmitter Power: | min: | max: |
Fiber Optic Receiver Sensitivity: | min: | max: |
Link Budget: | 16.0 dB |
|
| 1310 nm single mode | |
Fiber Optic Transmitter Power: | min: | max: |
Fiber Optic Receiver Sensitivity: | min: | max: |
Link Budget: | 19.0 dB |
|
NOTE: The fiber optic transmitters on this device meet Class I Laser safety requirements per
10 | techsupport@transition.com | 11 |
