Trek SSDVPF-CNE, SSDVPF-CNM, SSDVST-CNE, SSDVST-CNM TABLE OF CONTENTS

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

TABLE OF CONTENTS

Packaging .........................................Page 2

Introduction ......................................Page 2

General Information ..........................Page 2

New York City Approval .....................Page 3

Requirements for the

Commonwealth of Massachusetts .Page 4

Safety & Warning Information ..........Page 5

Cold Climate Insulation .....................Page 5

Location ............................................Page 6

Manufactured Home Requirements ..Page 6

Vent Termination Clearances ............Page 7

Appliance and Vent Clearances .........Page 9

Detailed Installation Steps .................Page 10

Typical Installation Sequence ...........Page 10

Step 1. Framing .................................Page 10

Step 2. Routing Gas Line ..................Page 10

Fireplace Speciﬁ cations .....................Page 11

Step 3. Install the Vent System .........Page 13

Vent Restrictor Installation ................Page 13

Vertical Termination Systems ............Page 14

Vent Section Length Chart ................Page 14

Vertical Vent Figures and Tables ........Page 17

Horizontal Termination System .........Page 19

Horizontal Vent Figures and Tables ...Page 21

Venting Using Flexible Vent Pipe .......Page 24

Step 4. Field Wiring .........................Page 25

Step 5. Optional Blower Kit Wiring ..Page 26

Step 6. Connecting Gas Line ...........Page 27

Step 7. Checking Operation .............Page 28

Step 8. Install logs, Volcanic Stone

& Embers ...........................Page 28

Step 9. Installing Glass

Enclosure Panels ............................Page 29

Step 10. Burner Adjustments ............Page 29

Step 11. Hood Installation .................Page 30

Finishing Requirements ....................Page 30

Installation Accessories ....................Page 31

Gas Conversion Kits ..................Page 33

This installation manual will help you obtain a

safe, efﬁ cient, dependable installation for the

appliance and vent system.

Please read and understand these

instructions before beginning your

installation.

The Millivolt appliances have a millivolt gas

control valve with piezo ignition system which

provides safe, efﬁ cient operation. If any optional

accessories that will require electrical power are to

be installed, the electrical power must be provided

at the time of appliance installation.

The Electronic appliances have an electronic

intermittent pilot ignition system which provides

safe, efﬁ cient operation. External electrical power

is required to operate these appliances.

PACKAGING

The assembled vented gas ﬁ replace heater is

packaged with:

1 - One log set located in ﬁ rebox area.

2 - One plastic bag of glowing embers and a

plastic bag of volcanic stone located in the

control compartment.

3 - One envelope containing the literature pack-

age, located in the ﬁ rebox which consists

of the homeowner's manual, installation

instructions, warranty, nailing ﬂ anges (8

for SSDVST models and 4 for SSDVPF

models).

4 - One vent restrictor (to be applied as shown

on Page 13; restrictor is taped to the enve-

lope).

5 - Hoods (2 for SSDVST models and 3 for

SSDVPF models), taped to the top of the

ﬁ replace.

6 - Carton Support (must be removed from the

control compartment prior to ﬁ rst burn-

ing).

INTRODUCTION

These vented gas ﬁ replace heaters are sealed

combustion, air circulating gas ﬁ replaces de-

signed for residential applications.

Approved Vent Components - These ﬁ replaces

are designed, tested and listed for operation

and installation with, the following vent com-

ponents only:

• Secure Vent™ Direct Vent System Compo-

nents,

• Secure Flex™ Flexible Vent Components

manufactured by Security Chimneys Inter-

national and

• Z-FLEX™ Model GA Venting Systems listed

to UL1777 and ULCS635 manufactured by

Flexmaster Canada Limited.

These approved vent system components are

labeled for identiﬁ cation. DO NOT use any other

manufacturer’s vent components with these

appliances. Use only the correct size venting

(4-1/2" inner & 7-1/2" outer).

These appliances comply with National Safety

Standards and are tested and listed by OMNI-

Test Laboratories, Inc. (Report No. 116-F-32-5)

to ANSI Z21.88b-2003 (in Canada, CSA-2.33b-

2003), and CAN/CGA-2.17-M91 in both USA and

Canada, as vented gas ﬁ replace heaters.

Both millivolt and electronic versions of

these appliances are listed by OMNI-Test

Laboratories for installation in bedrooms

and Manufactured Homes.

Manufactured Homes -

See Manufactured Home Requirements on

Page 6 for additional information.

WARNING

Improper installation, adjust-ment, alteration, service or maintenance can cause injury or property damage. Refer to this manual. For assistance or additional information consult a qualified installer, service agency or the gas supplier.

This appliance is only for use with the type

of gas indicated on the rating plate. This ap-

pliance is not convertible for use with other

gases, unless a certiﬁ ed kit is used.

Cet appareil doit être utilisé uniquement

avec les types de gaz indiqués sur la plaque

signalétique. Ne pas l'utiliser avec d'autres

gaz sauf si un kit de conversion certiﬁ é est

installé.

Misc. Codes / Standards -

The Installation must conform to local codes or,

in the absence of local codes, with the National

Fuel Gas Code, ANSI Z223.1 / NFPA 54 - latest

edition, or the Natural Gas and Propane Instal-

lation Code, CSA B149.1 - latest edition.

The appliance, when installed, must be elec-

trically grounded & wired in accordance with

local codes or, in the absence of local codes,

with the National Electrical Code, ANSI / NFPA

70-latest edition, or the Canadian Electrical

Code, CSA C22.1 - latest edition.

GENERAL INFORMATION

Note: Installation and repair should be per-

formed by a qualiﬁ ed service person. The

appliance should be inspected annually by

a qualiﬁ ed professional service technician.

More frequent inspections and cleanings may

be required due to excessive lint from carpet-

ing, bedding material, etc. It is imperative

that the control compartment, burners and

circulating air passage ways of the appliance

be kept clean.

S'assurer que le brùleur et le compartiment des

commandes sont propres. Voir les instructions

d'installation et d'utilisation qui accompagnent

l'appareil.

Provide adequate clearances around air open-

ings and adequate accessibility clearance for

service and proper operation. Never obstruct

the front or back viewing surfaces of the ap-

pliance.

These millivolt and electronic ﬁ replaces are

designed to operate on natural gas or propane

gas only. The use of other fuels or combination

of fuels will degrade the performance of this

system and may be dangerous.