Trek SSDVPF-CNE, SSDVPF-CNM, SSDVST-CNE, SSDVST-CNM

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. 29

The log set foam package is located in the ﬁ rebox

and the bags of decorative volcanic stone and

the glowing embers (rockwool) are located in

the control compartment. Refer to the following

information and Figures 52 and 54 for detailed

placement instructions.

Install the decorative volcanic stone and

glowing embers (rockwool):

Spread the decorative volcanic stone on the

simulated brick ﬂ oor of the ﬁ rebox around

the burners to simulate ashes. Maintain a 1/2

inch (13 mm) gap between the bottom of the

horizontal grate section and the top of the pile

of decorative volcanic stone. Place a few dime-

sized pieces of the glowing ember material

on the pan burner in front of the burned out

area on both sides of the log set. The glowing

embers may touch one another, but should not

overlap each other.

Install the unitized log set:

a. The bottom of the log set is notched to ac-

commodate the pilot.

b. Place the log set so that the four inner notches

on the underside of the log set ﬁ t over the

four risers located on the burner ends. See

Figure 52. This procedure is accomplished

primarily by feel, as the log set masks the

burner risers as it is being installed.

c. As a ﬁ nal check for correct log set placement,

check that the four outer notches on the

underside of the log set ﬁ t over the burner

tines as indicated in Figure 52.

WARNING

If logs are not installed according

to the log installation instruc-

tions, ﬂ ame impingement and

improper combustion could

occur and result in soot and/or

excessive production of carbon

monoxide (CO), a colorless,

odorless, toxic gas.

LOG & VOLCANIC STONE INSTALLATION

PROCEDURE:

Step 9. INSTALLING THE GLASS DOOR

WARNING

Handle this glass with extreme

care! Tempered glass is suscep-

tible to damage – do not scratch

or handle roughly while reinstall-

ing the glass door frame.

WARNING

Do not operate appliance with

the glass front removed, cracked

or broken. Replacement of

the glass should be done by a

licensed or qualiﬁ ed service

technician.

WARNING

Do not attempt to substitute the

materials used on this door, or

replace cracked or broken glass

with any materials other than

those provided by the appliance

manufacturer.

WARNING

The glass door of this appli-

ance must only be replaced as a

complete unit as provided by the

manufacturer. Do not attempt to

replace broken, cracked or chipped

glass separately.

WARNING

Do not attempt to touch the front

enclosure glass with your hands

while the ﬁ replace is in use.

Removing Glass Enclosure Panels

(see Figure 55)

1. Remove the top louver assembly by lifting it

up and pulling it out.

2. Remove the control compartment access

door (see removal instructions on Page 27

- Removing Control Compartment Door).

3. Locate the two (2) latches at the top of the

control compartment. To disengage the two

latches from the bottom vee-ﬂ ange of the

glass enclosure panel, reach for the handles

located towards the back of the latches and

pull the handles down toward the front of

the appliance.

4. Swing the bottom of the door out and raise

it slightly to lift the top ﬂ ange of the door

frame away from the appliance.

Installing Glass Enclosure Panels

(see Figure 55)

1. Visually inspect the gasket on the backside of the

glass panel. The gasket surface must be clean,

free of irregularities and seated ﬁ rmly.

2. Position the glass enclosure panel in front of

the ﬁ rebox opening at a 45 degree angle and

engage the top ﬂ ange over the lip at the top

of the ﬁ rebox opening. See Figure 55.

3. Swing the glass enclosure panel down and

back. Ensure the gasket seats evenly as the

panel draws shut. Engage the Vee-ﬂ ange at

the bottom of the panel with the latches and

close the latches to secure the panel.

4. Reinstall top louver assembly and control

compartment door see installation instructions

on Page 27, Reinstalling Control Compart-

ment Door).

Step 10. BURNER ADJUSTMENTS

Flame Appearance and sooting

Proper ﬂ ame appearance is a ﬂ ame which is

blue at the base and becomes yellowish-orange

in the body of the ﬂ ame. When the appliance

is ﬁ rst lit, the entire ﬂ ame may be blue and will

gradually turn yellowish-orange during the ﬁ rst

15 minutes of operation. If after a short period

the ﬂ ame stays lowered blue, or if the ﬂ ame is

orange with evidence of sooting (black tip), the

air shutter opening may need to be adjusted.

If the air shutter openings closed too far, sooting

may develop. Sooting is indicated by black puffs

developing at the tips of very long orange ﬂ ames.

Sooting results in black deposits forming on the

logs, appliance inside surfaces and on exterior

surfaces adjacent to the vent termination. Soot-

ing is caused by incomplete combustion in the

ﬂ ames and lack of combustion air entering the

air shutter opening. To achieve a warm yellow-

ish-orange ﬂ ame with an orange body that does

not soot, the shutter opening must be adjusted

between these two extremes.

Air Shutter Adjustment Guidelines

• If there is smoke or soot present, ﬁ rst check

the log set positioning to ensure that the

ﬂ ames are not impinging on any of the logs.

If the log set is properly positioned and a

sooting condition still exists, then the air

shutter opening should be increased.

Figure 55 - INSTALLING GLASS DOOR

Top Flange on

Glass Door

Bottom Vee-ﬂ ange

Glass Door

Glass Door Latch

Glass Door

Firebox Floor