Trek SSDVPF-CNE, SSDVPF-CNM, SSDVST-CNE, SSDVST-CNM - page 35

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. 35

Figure 63

Figure 64

BURNER POSITIONING

REAR BURNER

FRONT BURNER

PILOT

BURNER

Note: The burners are not identical. Position them so

that the circular burner ports run as shown. Note

especially the vertical run of ports relative to the pilot

burner. Bracket A on the rear burner will interfere with

the pilot burner if an attempt is made to install the

rear burner in the front burner’s position.

BRACKET A BURNER

PORTS

NOTE: INSTALL REAR BURNER FIRST,

THEN FRONT BURNER.

BURNER ORIFICE

Step 9. Reassemble the remaining components

by reversing the procedures outlined in the

preceding steps. Use pipe joint compound or

Teﬂ on tape on all pipe ﬁ ttings before installing

(ensure propane resistant compounds are used

in propane applications, do not use pipe joint

compounds on ﬂ are ﬁ ttings).

Step 10. Attach the conversion label provided

in the conversion kit to the rating plate on the

appliance.

Step 11. Turn on gas supply and test for gas

leaks.

Contents

Main INSTALLATION INSTRUCTIONS MODELS DIRECT VENT MULTI-OPEN SERIES TABLE OF CONTENTS Please read and understand these instructions before beginning your installation. PACKAGING INTRODUCTION GENERAL INFORMATION Table 1 Table 6 Figure 2 Tables 3, 4 and 5 show the appliances' gas pressure requirements: Table 3 Requirements for the Commonwealth of Massachusetts Installation Of Carbon Monoxide Detectors Approved Carbon Monoxide Detectors Signage Inspection Page Figure 3 LOCATION MANUFACTURED HOME REQUIREMENTS CAUTIONS Vertical Vent Termination Clearances VENT TERMINATION CLEARANCES Figure 4 - Gas Vent Rule Figure 5 Side Elevation View Horizontal Vent Termination Clearances Horizontal Vent Termination Clearances EXTERIOR HORIZONTAL VENT TERMINATION CLEARANCE REQUIREMENTS X A Minimum Clearances Canadian Installation * US Installation ** Figure 6 MINIMUM CLEARANCES TO COMBUSTIBLES Table 7 Figure 9 Figure 7 Figure 8 - DETAILED INSTALLATION STEPS TYPICAL INSTALLATION SEQUENCE Figure 11 - Figure 12 - Step 1. FRAMING Figure 13 Left Side View Cat. No. Top View Stepped to Accept Drywall(all 4 corners) Model Ship Wt. Figure 14 FIREPLACE SPECIFICATIONS - SSDVPF (PENINSULA VIEW) A Top View Left Side View Figure 17 Figure 16 - Figure 15 - Step 3. INSTALL THE VENT SYSTEM Figure 18 Figure 19 Figure 20 Figure 21 Figure 22 Figure 23 Figure 30 - Side Vent - THREE ELBOWS VERTICAL VENT FIGURES / TABLES (CONTINUED) Figure 31 - Top Vent - THREE ELBOWS Figure 32 - IMPORTANT Figure 34 Figure 33 - HORIZONTAL VENT FIGURES/TABLES WARNING Figure 36 Under no circumstances, may separate sections of concentric exible vent pipe be joined together. Figure 35 Figure 41 SECURE FLEX Figure 42 Figure 43 - Step 4. FIELD WIRING IMPORTANT NOTE 26 Ensure that wires are positioned away from hot surfaces and sharp edges. W Figure 46 Optional Control Switch Schematic Representation Only WARNING Never use an open ame to check for leaks. Step 6. CONNECTING GAS LINE Figure 47 CONTROL COMPARTMENT ACCESS/LOUVER PANEL INSTRUCTIONS (Ref. Figure 49) Step 8. INSTALLING LOG SET, VOLCANIC STONE AND GLOWING EMBERS Figure 54 Figure 52 Figure 50 Step 7. CHECK APPLIANCE OPERATION Page Ensure glass panels are in place and sealed during adjustment. Figure 56 Burner Air Shutter Adjustment Procedure Figure 57 Step 11. HOOD INSTALLATION INSTALLATION ACCESSORIES 32 H1988 CTSA-33 * H1986 CTSO-46 H1987 CTSO-44 H1985 CTSO-33 , 10 Pack CANADA ONLY LE CANADA SEULEMENT Figure 60 Figure 59 Table 14 Figure 61 Figure 62