
PDU Rackmount | Owner’s Manual |
Power Strips |
Designed for Mounting in 19 in. Racks | |
IMPORTANT SAFETY INSTRUCTIONS. This manual contains information concerning the proper installation and use of Tripp Lite’s Rackmount Power Strips. SAVE THESE INSTRUCTIONS.
Do not connect your power strip to an ungrounded outlet. Do not use it with extension cords or adapters that eliminate its connection to ground. Your power strip is designed for indoor use only. Install it away from heat emitting devices such as radiators and heat registers. Do not install where excessive moisture or other conductive contaminants are present. Never install electrical wiring during a lightning storm.
| Installation | |
| 1U Rackmount Installation | |
| To Mount Unit in Rack: Put four user-supplied rackmount screws (A) through the unit’s | |
| mounting ears (B) and into the rack rails as shown. The user must determine the fitness of the | |
| rackmount screws to hold the unit in the rack before installation. | |
| 0U Rackmount Installation | 1U Rackmount Installation |
| 1. Reorient Mounting Ears: Unscrew the screws (A) holding the unit’s mounting ears (B) to |
| |
| the sides of the unit. Use the screws from Step 1 (A) to reattach the mounting ears (B) to the | |
| unit as shown. Use only the manufacturer-supplied screws or their equivalent (#6-32, ¼" flat | |
| head) to reattach the mounting ears. | |
2. Mount Unit on Outside of Rack Rails: Put four user-supplied screws (C) or similar mounting hardware through the unit’s mounting ears (B) and into the side of the rack as shown. The user must determine the fitness of the user-supplied mounting hardware to support the unit before mounting.
Wallmount/Under Counter Installation
0U Rackmount Installation
Reorient the unit’s mounting ears as per the 0U Rackmount Installation above, then put four user-supplied screws or similar mounting hardware through the unit’s mounting ears and into the mounting surface. The user must determine the fitness of the user-supplied mounting hardware to support the unit before mounting.
Features
Circuit Breaker(s)
If the current draw of the equipment connected to your power strip exceeds your model’s Maximum Load Rating (see Specifications) for longer than a few seconds, a circuit breaker will trip to prevent any possible damage. When a circuit breaker trips, its plunger will pop up. Remove excess equipment and allow the breaker to cool one minute before depressing its plunger to reset the breaker. Caution (PDU2430 model only): If you depress the circuit breaker plunger during normal operation of your PDU, power will be interrupted to the receptacles and connected equipment will not be protected.
Grounding Lug
Use this screw (located by the power strip’s receptacles) to connect your power strip to ground.
Input Receptacle (IEC Model Only)
The PDU12IEC has no power cord. Instead, it has a IEC C20 input receptacle. To connect a PDU12IEC to utility power, use a user-supplied detachable power cord with an IEC plug on one end and a plug appropriate to your local utility outlets on the other.
Specifications
Model: | PDU1215 | PDU1220 | PDU2430 | PDU12IEC |
Series: | AGIP120V6IPRM | AGIP120V20RM | AGAC120V30RM | AGIB24016RMPDU |
Nominal Voltage/Frequency: | 120V/50 or 60 Hz | 120V/50 or 60 Hz | 120V/50 or 60 Hz | 100V to 240V/50 or 60Hz |
Outlet Power Rating (amps): | 15 amps | 20 amps | 15 amps | 15 amps for 100V to 120V or 10 amps for 208 to 240V |
Maximum Load Rating (amps): | 15 amps | 20 amps | 24 amps | 16 amps |
AC Receptacles: | 12 x NEMA 5-15R | 12 x NEMA 5-15/20R | 24 x NEMA 5-15R | 12 x IEC320-C13 |
AC Line Cord: | 15', w/NEMA 5-15P plug | 15', w/NEMA 5-20P plug | 15', w/NEMA 5-30P plug | IEC320-C20 |
Circuit Breaker(s) (Resettable): | 15 amps | 20 amps | 2 x 15 amps | 2 x 16 amps |
Dimensions (HxWxD, inches): | 1¾ × 17¼ × 37/8 | 1¾ × 17¼ × 37/8 | 1¾ × 17¼ × 37/8 | 1¾ × 17¼ × 37/8 |
Approvals: | UR, cUR | UR, cUR | UL, cUL | CE |
Limited Lifetime Warranty
Seller warrants this product, if used in accordance with all applicable instructions, to be free from original defects in material and workmanship for its lifetime. If the product should prove defective in material or workmanship with- in that period, Seller will repair or replace the product, in its sole discretion. Service under this Warranty can only be obtained by your delivering or shipping the product (with all shipping or delivery charges prepaid) to: Tripp Lite, 1111 W. 35th Street, Chicago, IL 60609. Seller will pay return shipping charges. Call Tripp Lite at (773) 869-1234 before sending any equipment back for repair.
THIS WARRANTY DOES NOT APPLY TO NORMAL WEAR OR TO DAMAGE RESULTING FROM ACCIDENT, MISUSE, ABUSE OR NEGLECT. SELLER MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRAN- TY EXPRESSLY SET FORTH HEREIN. EXCEPT TO THE EXTEND PROHIBITED BY APPLICABLE LAW, ALL IMPLIED WARRANTIES, INCLUDING ALL WARRANTIES OF MERCHANTABILITY OR FITNESS, ARE LIMITED IN DURATION TO THE WARRANTY PERIOD SET FORTH ABOVE; AND THIS WARRANTY EXPRESSLY EXCLUDES ALL INCIDENTAL AND CONSEQUENTIAL DAMAGES. (Some states do not allow limitations on how long an implied warranty lasts, and some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This Warranty gives you specific legal rights, and you may have other rights which vary from jurisdiction to jurisdiction).
WARNING: The individual user should take care to determine prior to use whether this device is suitable, adequate or safe for the use intended. Since individual applications are subject to great variation, the manufacturer makes no representation or warranty as to the suitability or fitness of these devices for any specific application.
Policy of Tripp Lite is one of continuous improvement. Specifications are subject to change without notice.
1111 W. 35th Street Chicago, IL 60609 • Customer Support: (773) 869-1234 • www.tripplite.com • Copyright © 2003 Tripp Lite. All rights reserved.