Maintenance & Service
Your Inverter requires no maintenance and contains no
Limited Warranty
Tripp Lite warrants its Inverters to be free from defects in materials and workmanship for a period of 1 year from the date of initial purchase. Tripp Lite’s obligation under this warranty is limited to repairing or replacing (at its sole option) any such defective products. To obtain service under this warranty you must obtain a Returned Material Authorization (RMA) number from Tripp Lite or an authorized Tripp Lite service center. Products must be returned to Tripp Lite or an authorized Tripp Lite service center with transportation charges prepaid and must be accompanied by a brief description of the problem encountered and proof of date and place of purchase.
This warranty does not apply to equipment which has been damaged by accident, negligence or misapplication or has been altered or modified in any way, including opening of the unit’s casing for any reason. This warranty applies only to the original purchaser who must have properly registered the product within 10 days of purchase.
EXCEPT AS PROVIDED HEREIN, TRIPP LITE MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Some states do not permit limitation or exclusion of implied warranties; therefore, the aforesaid limitation(s) or exclusion(s) may not apply to the purchaser.
EXCEPT AS PROVIDED ABOVE, IN NO EVENT WILL TRIPP LITE BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF THIS PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Specifically, Tripp Lite is not liable for any costs, such as lost profits or revenue, loss of equipment, loss of use of equipment, loss of software, loss of data, costs of substitutes, claims by third parties, or otherwise.
Tripp Lite has a policy of continuous improvement. Specifications are subject to change without notice.
Troubleshooting
| Please check the following before sending the Inverter in for service: |
|
|
| ||
| Symptom |
| Problem |
| Correction |
|
|
|
|
| |||
|
|
|
|
|
|
|
| Alarm sounds. |
| Low battery voltage (<10.5 V). |
| Turn Inverter OFF and run engine to recharge |
|
|
|
|
|
| vehicle battery. |
|
|
|
|
|
|
|
|
|
|
| Output overload. |
| Turn Inverter OFF and remove overload by unplugging |
|
|
|
|
|
|
| |
|
|
|
|
| Inverter's maximum continuous output power |
|
|
|
|
|
| (see Specifications). |
|
| Inverter does not turn ON when power switch is turned ON. |
| Automatic Inverter shutdown due to low battery voltage (<10V). |
| Turn Inverter OFF and run engine to recharge |
|
|
|
|
|
| vehicle battery. |
|
|
|
|
|
|
|
|
|
|
| Automatic Inverter shutdown due to output overload. |
| Turn Inverter OFF and remove overload by unplugging |
|
|
|
|
|
|
| |
|
|
|
|
| Inverter’s maximum continuous output power |
|
|
|
|
|
| (see Specifications). |
|
|
|
| Blown fuse. |
| Replace fuse with standard automotive fuse of identical |
|
|
|
|
|
| amperage (see Specifications). |
|
| Inverter is unable to power connected equipment. |
| Battery running low. Low battery voltage reduces |
| Turn Inverter OFF and run engine to recharge |
|
|
|
| Inverter power output. |
| vehicle battery. |
|
|
|
|
|
|
|
|
|
|
| Connected equipment load exceeds Inverter’s maximum |
| Turn Inverter OFF and remove overload by unplugging |
|
|
|
| continuous output power. |
|
| |
|
|
|
|
| Inverter's maximum continuous output power |
|
|
|
|
|
| (see Specifications). |
|
| Connected equipment experiences audio/video distortion. |
| Loose connections. |
| Check and secure all connections. |
|
|
|
| Audio/video interference. |
| Reposition equipment antennas and Inverter. |
|
|
|
|
|
|
|
|
| Specifications |
|
|
|
|
|
|
|
|
|
|
|
|
Model: | PV150 | PV375 | PV500 | PV600 |
Output Power (Maximum Continuous Watts):* | 150 | 375 | 500 | 600 |
Output Power (Peak Watts):** | 300 | 600 | 1000 | 1000 |
Input Voltage (DC): | 12V nominal | 12V nominal | 12V nominal | 12V nominal |
Output Voltage (AC)/Frequency: | 120V / 60 Hz. nominal | 120V / 60 Hz. nominal | 120V / 60 Hz. nominal | 120V / 60 Hz. nominal |
Output Waveform: | PWM Sine Wave | PWM Sine Wave | PWM Sine Wave | PWM Sine Wave |
Low Battery Voltage Alarm (Volts): | 10.5V | 10.5V | 10.5V | 10.5V |
Low Battery Voltage Shutdown (Volts): | 10V | 10V | 10V | 10V |
AC Outlets: | 1 | 2 | 3 | 3 |
Circuit Protection (DC Overload): | Two | Two |
*Maximum output power (continuous or peak) only available when vehicle battery is properly charged. Run vehicle engine often to maintain proper charge. ** Peak Output Power is instantaneous. The policy of Tripp Lite is one of continuous improvement. Specifications are subject to change without notice.
Typical Runtimes Before Battery Recharge
Although you can operate your Inverter with your vehicle engine off, best results are usually attained with the engine running. Since the Inverter converts electrical energy (and doesn’t produce it), the Inverter’s performance is relative to the condition of your vehicle’s electrical system (battery, alternator and wiring). If other loads (air conditioner, heater, lights, etc.) are also using power, you may get less runtime.
| With Typical | With Typical | With Typical |
|
| Compact Vehicle (4 cylinder) | |||
| Battery, Alternator | Battery, Alternator | Battery, Alternator | |
| & Wiring | & Wiring | & Wiring | |
|
|
|
|
|
Model: PV150 |
|
|
|
|
|
|
|
|
|
1/2 Load (engine on/engine off) | ||||
|
|
|
|
|
Full Load (engine on/engine off) | ||||
|
|
|
|
|
Model: PV375 |
|
|
|
|
|
|
|
|
|
1/2 Load (engine on/engine off) | ||||
|
|
|
|
|
Full Load* (engine on/engine off) | continuous/30 | |||
|
|
|
|
|
Models: PV500 & PV600 |
|
|
|
|
|
|
|
|
|
1/2 Load (engine on/engine off) | continuous/not recommended | continuous/1 hour | continuous/2 hours | |
|
|
|
|
|
Full Load (engine on/engine off) | continuous/1 hour | |||
|
|
|
|
|
* If vehicle wiring is adequate. See “Vehicle Electrical System Limitations” at right.
Minimum Recommended Cable Sizing Chart (PV500 & PV600 only) Choose the correct wire gauge based on your equipment’s wattage load.
|
|
|
|
| Wire Gauge |
|
|
|
| |
Watts | 10 ga. | 8 ga. | Two 10 ga. | 6 ga. | 4 ga. | |||||
100 | 24 | ft. | 36 | ft. | 48 | ft. | 56 | ft. | 100 ft. | |
200 | 12 | ft. | 18 | ft. | 24 | ft. | 28 | ft. | 48 | ft. |
|
|
|
|
|
|
|
|
|
|
|
300 | 8 | ft. | 12 | ft. | 16 | ft. | 20 | ft. | 30 | ft. |
|
|
|
|
|
|
|
|
|
|
|
400 | 6 | ft. | 10 | ft. | 12 | ft. | 14 | ft. | 24 | ft. |
|
|
|
|
|
| |||||
500 | not recommended | 8 ft. | 10 ft. | 12 ft. | 18 ft. | |||||
|
|
|
|
|
| |||||
600 | not recommended | 6 ft. | 8 ft. | 10 ft. | 15 ft. | |||||
Note: acceptable power is directly related to cable length (i.e.: the shorter the cable, the better the performance).
Vehicle Electrical System Limitations
NOTE: Due to the limitations of certain vehicles’ 12V DC lighter/accessory outlet electrical systems, you may not be able to continuously run a full load (375 watts) from PV375 models. If you regularly blow fuses, it may indicate your vehicle is not adequately wired to support a PV375 as it is designed. In this case, consult vehicle manufacturer recommendations for rewiring from the fuse block or battery with appropriate wiring (10 - 12 gauge) and fusing (at least 40 amp). All standard vehicle accessory outlet electrical systems can support full loads for PV150 models without any modifications.
Copyright © 2003 Tripp Lite. All rights reserved. PowerVerter is a registered trademark of Tripp Lite. | 200301121 |
|
