j.To reduce a fire hazard, keep machine free of grass, leaves, or other debris build-up. Clean up oil or fuel spillage and remove any fuel soaked debris.

k.Allow machine to cool at least 5 minutes before storing.

Operation

1.Do not put hands and feet near rotating parts or in the feeding chambers and discharge opening. Contact with the rotating impeller can amputate fingers, hands, and feet.

2.Before starting the machine, make sure the chipper chute, feed intake, and cutting chamber are empty and free of all debris.

3.Thoroughly inspect all material to be shredded and remove any metal, rocks, bottles, cans, or other foreign objects which could cause personal injury or damage to the machine.

4.If it becomes necessary to push material through the shredder hopper, use a small diameter stick. Do not use your hands or feet.

5.If the impeller strikes a foreign object or if your machine should start making an unusual noise or vibration, immediately shut the engine off. Allow the impeller to come to a complete stop. Disconnect the spark plug wire, ground it against the engine and perform the following steps:

a.Inspect for damage.

b.Repair or replace any damaged parts.

c.Check for any loose parts and tighten to assure continued safe operation.

6.Do not allow an accumulation of processed material to build up in the discharge area. This can prevent proper discharge and result in kickback of material through the feed opening.

7.Do not attempt to shred or chip material larger than specified on the machine or in this manual. Personal injury or machine damage could result.

8.Never attempt to unclog either the feed intake or discharge opening while the engine is running. Shut the engine off, wait until all moving parts have stopped, disconnect the spark plug wire and ground it against the engine before clearing debris.

9.Never operate without the shredder hopper, chipper chute, or discharge chute properly attached to the machine. Never empty or change discharge

-

bag while the engine is running.

10.Keep all guards, deflectors and safety devices in place and operating properly.

11.Keep your face and body back and to the side of the chipper chute while feeding material into the machine to avoid accidental kickback injuries.

12.Never operate this machine without good visibility or light.

13.Do not operate this machine on a paved, gravel or non-level surface.

14.Do not operate this machine while under the influence of alcohol or drugs.

15.Muffler and engine become hot and can cause a burn. Do not touch.

16.Never pick up or carry machine while the engine is running.

Maintenance And Storage

1.Never tamper with safety devices. Check their proper operation regularly.

2.Check bolts and screws for proper tightness at frequent intervals to keep the machine in safe working condition. Also, visually inspect machine for any damage and repair, if needed.

3.Before cleaning, repairing, or inspecting, stop the engine and make certain the impeller and all moving parts have stopped. Disconnect the spark plug wire and ground it against the engine to prevent unintended starting.

4.Do not change the engine governor settings or overspeed the engine. The governor controls the maximum safe operating speed of the engine.

5.Maintain or replace safety and instruction labels, as necessary.

6.Follow this manual for safe loading, unloading, transporting, and storage of this machine.

7.Never store the machine or fuel container inside where there is an open flame, spark or pilot light such as a water heater, furnace, clothes dryer, etc.

8.Always refer to the operator’s manual for proper instructions on off-season storage.

9.If the fuel tank has to be drained, do this outdoors.

10.Observe proper disposal laws and regulations for gas, oil, etc. to protect the environment.

4

Page 4
Image 4
Troy-Bilt 494 manual Operation, Maintenance And Storage

494 specifications

The Troy-Bilt 494 is a powerful and versatile garden tiller designed to make soil preparation an efficient and straightforward task. With its sturdy construction and innovative features, it is a favored choice among both gardening enthusiasts and professional landscapers.

At the heart of the Troy-Bilt 494 is its robust engine that delivers reliable power and performance. The tiller is equipped with a powerful four-cycle engine that ensures consistent torque and efficiency. This engine provides ample power to break up tough soil, allowing users to tackle any gardening project with ease.

One of the standout features of the Troy-Bilt 494 is its counter-rotating tines. This technology allows the tines to rotate in the opposite direction of the tiller, effectively cutting through hard soil and mixing in organic matter like compost and mulch. The counter-rotating action helps to aerate the soil better, promoting healthier root growth and improving overall soil quality.

The tiller's adjustable tilling width is another significant characteristic. Users have the flexibility to choose between different widths, allowing for versatile use in various garden sizes and layouts. This feature makes it easy to navigate around plants and other obstacles, ensuring that every inch of the garden can be cultivated effectively.

User comfort is also a priority with the Troy-Bilt 494. The tiller comes with soft-grip handles that reduce fatigue during extended use, making it comfortable for gardeners of all experience levels. Additionally, its lightweight design enhances maneuverability, ensuring that users can navigate tight spaces easily.

The durability of the Troy-Bilt 494 cannot be understated. Built with high-quality materials, it can withstand the rigors of frequent use and demanding gardening tasks. Its heavy-duty frame is designed to handle tough working conditions while providing stability and control during operation.

In terms of maintenance, the Troy-Bilt 494 is designed for ease of use. With accessible components, regular maintenance tasks such as oil changes and spark plug replacements can be performed without hassle. This commitment to user-friendly design ensures that gardeners spend more time tilling and less time on upkeep.

Whether you're preparing a new garden bed, mixing in compost, or cultivating between rows, the Troy-Bilt 494 tiller combines power, efficiency, and user-friendly features, making it an essential tool for anyone serious about gardening.