3.Disconnect the log cradle from the beam on the side of the control valve. See Figure 3-5.

4.Lift and slide the cylinder up to the top of beam and into the weld brackets. See Figure 3-6.

5.Attach the dislodger over the wedge assembly and secure with hardware, previously removed, to the weld brackets.

NOTE: Once the six hex screws are tightened, there may be a slight gap between the dislodger and the weld brackets. This gap is normal.

6.Reattach the log cradle to the side of the beam with the control valve, aligning the ends of the cradle with the beam flanges.

7.Roll log splitter off the bottom crate.

Preparing the Log Splitter

1.Lubricate the beam area (where the splitting wedge will slide) with engine oil; do not use grease.

2.Remove vented reservoir dipstick, which is located in front of the engine on top of the reservoir tank. See Figure 3-7.

IMPORTANT: The log splitter may have been shipped and primed with hydraulic fluid in the reservoir tank. If not, proceed with the following steps:

3.Fill the reservoir tank with hydraulic fluid included with this unit (if equipped) or approved fluids which include Dexron® III / Mercon® III automatic transmission fluid, a 10 Weight AW hydraulic oil or Pro-Mix™ AW-32 Hydraulic Oil.

4.Check fluid level using the dipstick. See Figure 3-7. Do not overfill.

5.Replace vented dipstick securely, tightening it until the top of the threads are flush with top of the pipe.

6.Disconnect the spark plug and prime the pump by pulling the recoil starter as far as it will go. Repeat approximately 10 times.

7.Reconnect the spark plug wire and start engine following instructions in the OPERATION section.

8.Use control handle to engage the wedge to the farthest extended position. Then retract the wedge.

9.Refill tank as specified on the dipstick.

NOTE: Failure to refill the tank will void unit’s warranty.

10.Extend and retract the wedge 12 complete cycles to remove trapped air in the system (the system is “self-bleeding”).

11.Refill reservoir within range marked on the dipstick.

WARNING: Much of the original

fluid has been drawn into the cylinder and hoses. Make certain to refill the reservoir to prevent damage to the hydraulic pump.

Figure 3-5

Figure 3-6

Figure 3-7

NOTE: Some fluid may overflow from the vent plug as the system builds heat and the fluid expands and seeks a balanced level.

3

Setting Up

Your Log

Splitter

WARNING

Much of the original fluid has been drawn into the cylinder and hoses. Make certain to refill the reservoir to prevent damage to the hydraulic pump.

IMPORTANT: The log splitter may have been shipped and primed with hydraulic fluid in the reservoir tank. If not, proceed with the following steps:

NOTE: Some fluid may overflow from the vent plug as the system builds heat and the fluid expands and seeks a balanced level.

7

Page 6 Page 8
Page 7
Image 7
Troy-Bilt 570 manual Preparing the Log Splitter
Page 6 Page 8

570 specifications

The Troy-Bilt 570 is an exceptional cultivator designed for both amateur and professional gardeners, making tasks like tilling and cultivating soil easy and efficient. With its robust construction and innovative features, it caters to users looking for reliability and performance in their gardening tools.

One of the standout features of the Troy-Bilt 570 is its powerful engine. It typically comes equipped with a dependable 170cc OHV engine, providing ample power to tackle tough soil conditions. The engine is designed for easy starting, which eliminates the frustration often associated with garden equipment. The performance is consistent, even when working in hard or compacted soil, making it a go-to choice for users with demanding gardening needs.

The Troy-Bilt 570 utilizes a counter-rotating tilling technology, which helps in breaking up tough soil and mixing in organic material with greater efficiency. This feature is crucial for promoting healthy plant growth, as it allows for better aeration and nutrient distribution within the soil. With its 16-inch tilling width, the Troy-Bilt 570 can cover large areas in a shorter amount of time, making it ideal for larger gardens or landscaping projects.

Another impressive characteristic of the Troy-Bilt 570 is its adjustable tilling depth. Users can easily modify the depth to meet their specific gardening requirements, whether they are preparing the ground for planting, aerating, or simply mixing in compost. The depth ranges from shallow to deep, allowing for versatility in various gardening tasks.

Ease of use is further enhanced by the cultivator's comfortable, ergonomic grips, which minimize fatigue during extended use. The cultivator also features a lightweight design, making it easy to maneuver around the garden or landscape. Additionally, the Troy-Bilt 570 comes with a variety of attachments, allowing users to customize their gardening experience further, whether it be for weeding, planting, or breaking ground.

In terms of durability, the Troy-Bilt 570 is built with high-quality materials, ensuring it can withstand the rigors of outdoor use over the years. The cultivator is also relatively easy to maintain, with accessible components that simplify repairs and upkeep.

In conclusion, the Troy-Bilt 570 cultivator stands out for its power, versatility, and user-friendly design. Its innovative features and technologies make gardening more efficient and enjoyable, providing gardeners with the tools they need for successful cultivation and landscaping projects.
Top Page Image Contents