Section 4: Operation

WARNING

The HIGH speed belt range position combined with a FAST wheel speed setting propels the tiller at the fastest pace. Reduce the engine throttle speed when starting out to help avoid personal injury or property damage if using this speed combination.

3.Kneel on left side of tiller. To create belt slack, reach over to right side of the pulleys and push in at the center of the belt with a finger. At the same time, use your left hand to work the belt part-way onto the lower-front transmission pulley groove (Figure 4-10).

Figure 4-10: Low range to high range. Shows moving belt from lower-rear groove onto lower-front groove.

4.Go to the other side of the tiller to finish seating the belt onto the pulley groove.

5.Working from the left side of the tiller, work the belt as much as possible onto the top-front engine pulley groove (Figure 4-11).

6.Finish seating the belt from the right side of the tiller.

IMPORTANT: Proper belt tension is important for good performance. See Section 5, Drive Belt Maintenance for information on belt maintenance schedule and procedures.

NOTE: If extra belt slack is needed to move the belt, just raise the Wheels/Tines/PTO Drive Lever up into REVERSE. This lowers the engine pulley, and creates more slack.

Figure 4-11: Low range to high range. Shows moving belt from top- rear groove onto top-front groove.

7.Check both sides of the high range pulley grooves to verify that the belt is properly seated.

Changing Belt From HIGH Range to LOW Range

1.To avoid personal injury, shut off engine, let all moving parts come to a complete stop, then disconnect spark plug wire from spark plug and move wire away from spark plug before making any adjustments. Let engine and muffler cool.

2.Move the Wheels/Tines/PTO Drive Lever into NEUTRAL.

3.Stand on left side of tiller. Use your right hand to hold the Wheels/Tines/PTO Drive Lever up into REVERSE position. Use your left hand to move the belt off top-front engine pulley groove to top-rear engine pulley groove (Figure 4-12).

Figure 4-12: High range to low range. Shows moving belt from top- front groove onto top-rear pulley groove.

4.Go to right side of tiller and finish seating the belt.

5.Still holding the lever up in REVERSE position, and working from the left side of the tiller, move the belt from the lower- front transmission groove to the lower- rear transmission groove.

6.Go to the right side of the tiller and finish seating the belt (Figure 4-13).

Figure 4-13: High range to low range. Shows moving belt from lower-front onto lower-rear groove.

7.Check that the belt is fully seated in the pulley grooves. Check this from both sides of the tiller.

Choosing Wheel

and Tine Speeds

Your tiller has four FORWARD wheel/tine speed combinations for handling a variety of tilling tasks and gardening jobs. Exper- iment with the tine depth, engine speed, and wheel/tine speed and determine the combination that provides the best results. Here are some tips:

1.Advance the throttle lever so the engine has sufficient power.

2.When tilling untilled or hard earth, do not set the Depth Regulator too deep. The tiller will buck and the engine will load down.

3.You will know your settings are ideal when the tines break-up the soil easily, the engine does not labor, and your progress is steady and smooth.

See Table 2, Wheel Speed and Belt Range Selection Guide for recommendations.

20

Page 19 Page 21
Page 20
Image 20
Troy-Bilt 682J, E686N, E682L manual Choosing Wheel Tine Speeds, Changing Belt From High Range to LOW Range
Page 19 Page 21

682J, E686N, E682L specifications

The Troy-Bilt brand is widely recognized for its reliable outdoor power equipment, including a line of innovative lawn tractors. Among these, the Troy-Bilt 682J, E686N, and E682L stand out for their exceptional performance and user-friendly features, catering to various lawn care needs.

The Troy-Bilt 682J is a robust lawn tractor designed for efficiency and ease of use. Its 19 HP engine provides ample power for handling various landscaping tasks, while the 42-inch cutting deck allows for a wide cutting path, making quick work of mowing larger yards. The tractor boasts a six-speed transmission, enabling users to select the speed that best suits their mowing conditions. Additionally, the 682J features an ergonomic seat and steering for comfort during extended use, making it a solid choice for homeowners with medium to large properties.

The Troy-Bilt E686N takes things a step further with its advanced technology. This model integrates a 20 HP engine and a larger 46-inch cutting deck, enhancing productivity significantly. The E686N is equipped with a hydrostatic transmission, offering smooth operation and easier control, allowing users to maneuver around obstacles with precision. One of its standout features is the Easy Change Oil Kit, which simplifies maintenance, ensuring that the engine runs smoothly for longer periods. The inclusion of a washout port on the deck makes cleaning effortless, promoting better lawn health and equipment longevity.

For those seeking a more compact option, the Troy-Bilt E682L delivers reliable performance in a smaller package. This model features a 19 HP engine paired with a 38-inch cutting deck, perfect for navigating tighter spaces without compromising power. Its tight turning radius enhances maneuverability, making it ideal for suburban lawns with landscaping features and garden beds. The E682L is designed with user comfort in mind, featuring an adjustable seat and simple controls for intuitive operation.

In summary, the Troy-Bilt 682J, E686N, and E682L represent a dynamic trio of lawn tractors, each catering to various homeowner needs. With powerful engines, efficient cutting decks, and user-friendly features, these models are built to enhance the mowing experience. With their proven reliability and advanced technologies, Troy-Bilt tractors make maintaining a beautiful lawn a manageable task for anyone.
Top Page Image Contents